Відео

Fit as a fiddle 👍

We try our best 👍

The original ties were steel and they rust and pop(lift the beds a telltale sign of failing ties) so take down and rebuild drilling new ties into inner leaf then it’s all good, thanks for commenting and watching 👍

Always do our best 👍

Thank you for comment that’s the way I have always seen and done putting boards on just think it gives better strength 👍👍

Board is getting dabbed on to wall and plumber asked for some ply boards on wall also just for his fixings, just doing as asked to do, I suppose everyone has different views cheers for watching and also hit the subscribe 👍

Thank you 👍

Thank you 👍👍

Thank you 👍

Why? It’s spraying the hypo out thick

@@pgbricks911 perhaps the hypo just isn’t foamy in general but I’m sure you could cover much more surface in way less time with a wider and thicker cone idk

Thank you for pointing this out it’s something I will look into 👍hit the subscribe and like

Was knocking wall down and had a spare hour so done some drill holes ready for next day for cross stitching new brickwork in thanks

I pulled the outer skin down last week to repair damaged brickwork from a wheelie bin fire

Terrible standards, a barrat homes house would expect better, thanks for watching 👍

walls tie are their insulation has been taken out already joints are terrible

Insulation had been blown in but most was missing bad job by who ever blown it in 👍

@hod2116 ties was the old plastic type which were used about 30years ago not many in though 👍

Right depth for those particular concrete screws thanks for watching

It doesn’t we turn the pressure down on machine doesn’t do any damage we’ve been doing this for years with no damage only very happy customers, thanks for watching 👍

noah why dont you put a short video on to show the results using a brush ,,i clean loads of decking useing a surface cleaner with good results ,will only get any damage if the decking is rotten then it should be replaced ...lets see the brush work

Aye looking good 👍

Thank you 👍👍

To be fair mate I was working in very cramped conditions which you can’t see and odd bit going in compo isn’t the end of the world can’t control where bits fly off to, most bits don’t cause a problem if a bigger bit goes in just remove it, easier thing for people to criticise without knowing the conditions, thanks for watching and hopefully you will subscribe 👍

Every bricklayer has different ways, my way is put some courses on then insert insulation then add wall ties either cavity ties or in this case dog leg ties drilled in, just to stop insulation sagging and dropping on your hand while laying, this particular house didn’t have any insulation at all in house, hope that clears that up thanks

Thank you always try and lay them proper quality over quantity is best, thanks for watching 👍👍

Leave a gap while laying bricks or blocks, if you don’t mortar in between them will make bricks/blocks bulge out not lay easily due to mortar in way, then once laid you fill gap up, I usually finish walls then go around the wall and fill the gaps up, hope that make sense and thanks for watching 😊

Aye we try our best at pd brickwork 👍👍

He’s starting to learn abit 😊

Pride in the job 👍

Yes and loads of weeds

I hope so 😂😂

Yes customer just said use his old bricks he had in yard, either getting render on or paint, not sure about planning I just turned up to build the two pillars 👍👍

@@pgbricks911 gg yeh 2.5 meters you can go b4 permission is needed hope that's helpful and yeh we do what we can for work so np we all need to earn

@@david-ul3ch Thanks for info 👍👍

Yes you right a bit of render will make it all look ok, customer had old bricks he wanted using so I just done as asked 👍

@@pgbricks911 money well saved in my eyes. Good good👌

Yes keeping mess down while we work 👍

Thanks for comment, are the fitzbrick any good, I’m just used to using corner blocks and pin in cross joint when you can’t get a corner block on

@pgbricks911 yeah clamp on upto 9inch work too real quick to use aswell

Cheers for that will get a pair of them and give them a go they look good 👍

Like it or not now we're manufacturers You can do it all😅

Just a favour for a friend that job 👍

The driver tries his best 😊

Yes customer said he is relaying some modern tiles over them old ones most of them are cracked 👍

I only laid bricks customer is covering with new tiles, I’m just the bricklayer 👍

Thank you 👍👍

Been most boring day for a long time 😂

Can’t knock your graft tho 🦾💯

Thank you 👍

No electric on job 👎👎

yes could of used a breaker if we knew we needed one,but we turned up at the job and the render was supposed of already been taken off,, so used the tools we had ,,no good letting the job beat you cause u havent got a machine..just get the job done

because we had travelled 50 mile to rebuild the gable peak so that was our job cheers@@andyfrndi6140

​@@gavyndavis1694 your right im sorry you got it done thats all that matters

cheers Andy we just needed to get the job done while we were there ,with out having to go back thanks, keep watching the channel thanks again Gavyn@@andyfrndi6140

He didn’t really like it 😂

​@@pgbricks911 How do you know? Kids like you shouldn't be in UA-cam.