- 8
- 30 669
Michał Dudziński
Приєднався 16 жов 2013
Відео
BMW R1100GS at Nürburgring Nordschleife
Переглядів 25 тис.7 років тому
Slastik robot 2.0
Переглядів 1708 років тому
delta 3D printer build time lapse
Переглядів 2,6 тис.8 років тому
3KU delta 3D printer from AliExpress: www.aliexpress.com/snapshot/7363019256.html?orderId=73126328946861
Slastik sunglasses robotic display by Fotoduda
Переглядів 2139 років тому
I build this robotic display to show off the magnetic Slastik sunglasses. It's using Arduino Leonardo and four servos. More info at fotoduda.com
Tor Poznan sekcja gokartowa BMW E39 530dA
Переглядів 3499 років тому
AEE MagiCam S51 action camera test
Переглядів 1,3 тис.9 років тому
things to fix: -camera angle on the helmet too low -wrong mic plug giving terrible wind noise
kwietnik vid
Переглядів 38910 років тому
Gdzie podpiloes nawigację
be carefull you could suddenly get catched from a stock peugeot speedfight
Very nice Round. Good Motorbike and an very good Driver! Not to much, safty first.
Nice
nice
Nice
lidos lentes xd
I plan getting same delta do you have any tips for us ? I will try tmc 2100 and get proper silicon heated bed Tnx
Welche Reifen bist du denn gefahren ?
Michelin Pilot Road 4 Trail. They are excellent on tarmac, specially in wet. Off road they are what they are :)
Thank you dude. I have the Continental Trail Attach 2 but they are to hard to drive faster on tarmac.
Recently I took part in a gravel rally, I was paired with a guy on a GS800 on Conti Trail Attacks, I honestly didn't see them perform that much better off road than my street tires. I think the only on/off road tires I would use are TKC 80 or K60. All other stuff with less thread makes no difference. PS here's a clip from the rally, my bike is the one on the ground all the time ;) ua-cam.com/video/C9msNYpW5IA/v-deo.html
hey, mam ta sama drukarke i jestem do tej pory bardzo zadowolony. Podjales jakies zmiany do tej pory?
hi I have same printer and it doesn't print higher that 3 mill. how does your prints come out, thanks.
Did you have problems uploading firmware.
where did you by the heatbed, i ordered one and i know its not included, how do you like yours sor far? i just ordered one today
+Steve Cesario I asked the supplier and they included it in the package for extra 25 bucks. I requires extra power supply that they also include.
how did you go with getting yours printing level. I have the same printer. It seems to print ok with objects in the center but as it moves out to the edges the hotend either ends up too low or too high.
+Shival Wolf Do you have the auto bed levelling included? It's a little probe with orange bottom and a LED on the top, attached to the hotend. It has to be adjusted just so the LED goes on when the nozzle is 0.2 - 0.5 mm from the table (requires some fine tuning later). Than you run a G29 command and it does it's magic. I also included that command in my slicer (Cura) G code, so it levels the bed every time before printing.
I did try that and i'm not sure whats up with the probe. it doesn't probe some parts of the bed and ends up off the edge so never triggers and dives right into the printbed. sometimes it also doesn't trigger even though its touching the plate. I have a feeling the probe might be faulty,
+Shival Wolf Mine is digging into the table when set too low. Than it goes all weird, stops probing in mid air etc. I lowered the probe, just a few twists of the locking nuts. Than it works all perfect. Try moving the hotend (when it's not hot) by hand around the table, see if there are any movement restrictions and if LED goes on when supposed. Check for loose brackets and loose cables. The probe itself should also be tightened properly, absolutely vertical.
thanks il give that a try
+Shival Wolf did it work?