Відео

Can you please get better lighting so we can see what you're doing also. Thank you

Where can I buy those parts?

I have same problem 😭😭

Would you know how to fix a code E115 on a Raymond walkie, please let me know, I can pay for your advise via PayPal… thank you..

Show the location of fuse box, where is it located in the diesel forklift. I didn't found it.

Good

Camera man is trash

Una imagen más amplia del sistema

Thank you very much for the great video it was helpful

What is Fault 47 forklifter voltas electric

I habe am old 90s crown forklift that wont go into foward or reverse but everything else functions what should I check first

How about jungheinrich forklift? I'm wait your videos

The lower capture plate is on upside down. good job security as the contacts will wear out faster.

I've done countless of these. I usually like to pull the entire assembly out and rebuild it on the bench if I can. I find this way more cumbersome.

Very nice

I remember the 210 panel

My Hastert 60 has no fork operation but still hear the contacts clicking can you help??

advanceforkliftparts.com does not exist.

I have have same unit which needs repair. Could you tell me where you bought your replacement parts?

Hi I have Toyota 7FBH20 Forklift but when accelerator presse so not working lifting Disconnected pump drive motor or not showing error can you help me sir... ..Toyota battery forklift.

does the fork lift need to plug to its battery?

Thanks for the helpful vid!

I have a forklift sometimes work sometimes doesn't work I have no idea what wrong with it

big forklift linda 2008 time problem I need help?

Working fast!!!!must be flat rate paid tech??

what does a -15 code mean on the dash of yale type e lift. trying to get batteries charged up but all we get is the horn. and the dash lights.

working on a yale warehouse lift. type E series three wheel setup. mast will not raise. is that a fuse type circuit? where are fuses located?

Could you do a video of an electric pallet jack from crown. It won't go up or down.

Thanks for the video, very well made. The nut on the back that you tightened with a 3/8" driver: how do you adjust it or do you just run it down until a small part of the threads are sticking out (so the nylock is grabbing?)

Crown FC ?

reverse steering forklift in order to make this sort of lift drive normal steering is it just done by programming it say on a Raymond standup program in it using its yoke or joystick or hand controller whichever term you want to use

It is a stupid question. But, maybe it's because I'm an Electrical Engineer. Nonetheless, he has no business working on equipment that he doesn't understand the basics of.

Hi, The best ideas that I have noticed was on Volt daddy (just google it) Without a doubt the most informative info on batteries and this same that i have found.

Hey guys, The best info that I have saw was on Volt daddy (just google it) Probably the most detailed info on batteries and this type of that I have found.

hi i am a 1 time owner op out to work from heavy lift world.. now trying to branch out..just my luck found a nice running lift 79 clark got it home move a few things around and then massive leak started from the main lift cylinder its a lark c 30 i can't even find a book on how to even try to fix ...thin i was told after i had bought a seal kit from cal lift in ca... it would be like performing brain surgery.. now i scared to try and tackle this. before i jump in would have have any vids on the subject ..i have pic iic you want to see... ty

Great repair! Liked the voice over, had to LOL with 7:42 "...guys with little girly hands gonna need a jib" to then be followed up 2 minutes later with 9:46 "would be nice to have smaller hands" LOL

Great work. Fast and efficient. Dont see so many of these old EV100s around any more, but I like the fact that they are serviceable. Newer all-in-one systems have only solution for everything, that is-replace the hideously expensive black box. By the way, I am with chuck7497 on this, you DO sound a lot like Tom Hanks. Is your day job in Hollywood, by any chance?

WHY YOU WORKING SO FAST..do it right.See you didnt test contactor tip bars.why?

Always raise Drive tires above the floor.

facebook.com/groups/forktech/

You should measure voltage across the fuse, positive on one side, negitive on the other. A fuse with high resistance will give you a false positive when you test them the way you are doing it.

I have a 36 volt crown sit down lift. The contactors only work on one out of two drive motors. I have voltage but the contactors still do not close. Its not the coils they seem to be ok. Plus it would be strange for two coils {fwd/rev} two go bad at the same time on the the same drive motor.

I HAVE A LP CLARK FORKLIFT USED TODAY AND IT STALLED ON ME ,TRIED TO START IT ,IT WONT IT TURNS OVER FASTER THEN IT DID BEFORE ANY IDEA ON WHATS GOING ON WITH IT???,IT MADE A FUNNY NOISE TODAY LIKE A BELT WAS SQEAKING, I LOOKED AT THE ENGINE FAN AS I TRIED TO START IT,,ALL BELTS ARE MOVING, BUT IT SEEMS TO BE TURNING OVER FASTER THEN IT WAS BEFORE IT STALLED ON ME ANY HELP GREATLY THANKFUL

Very Good Video

Have you set the settings on your card to specs Ev-100 lx need to be set with a controller to your truck.

Better and cheaper in the long run to replace entire contact assembly. Plastic gets old and brittle the plunger rod is usually the bigger problem along with that thin little shim.

You have the bottom black plastic guide on the wrong way, it has 2 tip guides on it. Anyone carrying out any work like this please disconnect the battery and remove Rings or watches as when they short out they turn into mini bar heaters on your fingers or wrist. Please if your not 100% sure what your doing don't touch. Call the service department.

Good video

yeah common problem especialy if the batteries are poorley charged ( opertunity charging) everything gets hot .... great video

Left out steps..If you're troubleshooting a contactor you do a drop test across the tips..then a resistance test on the coil to see if its shorted..