Відео

Thank you for this just found my old drill dr and had forgotten how to use it. Thanks again.

FluTe, not fluke- a drill bit has flutes, a fluke is a seldom seen occurrence. Two royal flush hands in a row are a fluke 😂

I never liked the plastics they used. It always felt like there was too much friction while doing the twisting of the assembly necessary to make the cuts.

Thank you. I was successful! Whoo hoo!

Does your not have a hoes going between the forks?

Thank you for teaching

It's easier to loosen the rear drive than deflate the tyre

How to replace blades

CX500 COOPER HABE ICH AUCH VIELE JAHRE GEFAHREN SUPER COOPER ❤❤

Thank you

Don't know who you are, but I like ya ! I got an '83 cx650 custom a month ago. I can't spend 400 to have 20 dollar seals put in. Decades ago, I did all my own work on my Triumphs....I'm 66 now, and I'm going to have to get her done. Looks like a pain, but like you said...just jump in the water and swim.It'll be fun ! Thinking of Bruce Willis's line in Die Hard...."Come to the coast; we'll have a few laughs". I will tell you this as a return favor, though. A guy who owns a bone yard said to get that ethanol gas outa my bike and buy clear gas.(86 octane,no ethanol)(it crystalizes and eats stuff) I pumped out all my old gas ,put the clear in with a shot of Stabil. The bike idled for a while, hacked and coughed and went Vrooom ! So I took it for a ride. Wow. It never felt like 64 horses before - oh it does now. Yeah, a bike from the 80's doesn't need corn; doesn't like corn. She's got her oats now. And what else is amazing...her cold starts. Cold weather, cold bike, full choke, key,button...vroom, just like that. Amazing. My Triumphs were first kick. Now, so's my Honda. Thanks.

IF YOU EVER GET A CHANCE TO DO A VIDEO ON HOW TO WIRE A IGNITECH TO A 79 CX500( CDI bike )...PLEASE DO SO ! i just bought a 79 cx500 that had one but it was wired incorrectly and is missing certain pins etc.

Mine is a hand me down, same model as yours. I was never taught how to actually use is. Sometimes I'd have success and sometimes I'd end up making the whole drill bit nearly flat if I didn't have it aligned right. I was trying to align it manually because i didn't realize that thing on the side was for getting proper alignment! Thank you sir.

Still using my Dads orig. Unit from the mid-nineties. Looks like the same model here.

What a great video ! Excellent filming and clear narration. Thank you.

Excellent instructions to assist us to do it ourselves. Looking to do the same and paint the lowers as you've done, on two Customs I have - one just bought and the other been sitting in my shed for 20+ years. And on the sitting one, the forks had just been done poorly by a shop just before it stopped running. The guy tapped some breather hole with drain hose in the top cap bolt. I can't recall the reason, but it leaked. So I will definitely be doing them myself.

Ahh

Im more interested in the hoop you've made.

Been searching for just this !

Very Nice💥 Thank you Sir!🛠

Nothing cool about ruining a bike for a stupid ass cafe racer, No one is racing and it looks stupid.

My original stanchions are rusty above the seals from stone chips and poor maintenance over the years... Is this a problem, or can you but replacement stanchions cheaply?

turn signals in those day did what they should these days I sometimes wonder ????

Yes you can use WD40 or something similar on the tire, but use a deck of playing ♥️♣️♠️♦️cards to go all the way around the tire under the rim. It works great!

Man are you doping that the hard way. Take the head apart to get all the old string out and put it back together. Line up the line on the winder and push the string IN from the outside and it will seat in place. Turn the feeder until the right length is sticking out and rock and roll dude. If it's a tad long it will self cut to the right length and you're back at work. Get good line...or you'll b changing it every 30 seconds.

Watched a lot of videos on this topic and no one talks about the correct location of the blades after assembly, for better ejection of cut grass 😥

Thanks for this video. There is a copper washer that goes in the bottom with the 8.. hex bolt as well as on the drain 6 mm bolt at the bottom of the fork tube. Just thinking of mentioning it. here. Thanks

This was very helpful. I wasn’t sure I was installing the deck correctly and after watching this video, I was able to get it done. Saved me work.

Incredibly helpful video. Thank you! Only video I've found demonstrating the swap with an electric pto

How’s the build going?

This is by far the best one I’ve found online I’ve been hoping someone would do it like this this is how I’d like to do great work!!

Will you be upload more videos? It looks like they were posted a year ago...Enjoying watching your work!

Where to buy this

Very informative video! I gather you have the electric PTO. I have avoided removing the deck because I bought a Mojack lift. My fabricated deck stays fairly clean. I do change my blades every season. If they can be sharpened, cleaned, and balanced, I will reuse them. Definitely, removing the deck is something every Cub Cadet owner should know how to do.

Bro iski buy link share kro

Great video now I will try replace the seals on my 82 gl500 forks

Thanx. Is there an angle setting on that? like 118° or 135°... I bought one 15 years ago, maybe longer, never ever used it.

jak nazywa się ten środek do czyszczenia silnika

I'm considering getting one of those attachments for my XT2. How reliable has the snowblower been for you? Is it low maintenance? TIA!

Brush paint it easyer

Nice video. About masking off the tyre: I've heard of a method where you put a small bit of hand grease (the stuff you put on your hands when they're dried out) right around the edges of the rim. This is easier to curve around the rim than with masking tape and you can easily wash it off with some soap and water after you've painted the wheel. Haven't tried it myself yet but it does sound like a solid method.

What size socket to remove the blades

kitne ki hai bai khha se li

Looked better before being painted, I just got the same bike that's been sprayed all black. And have to remove it now. Thanks for the videos tho

This is ridiculous !!! *unplug spark plugs (for safety) *jack front end up *use short piece of wood to keep blades from turning and remove nuts. Take old blades off. *put new blades on. *lower front end *done

I did learn the square hole trick thanks,previosly i used a socket on the the tension wheel to pull it to get belt on ,square hole makes good sense.

I've got an 82 GL500 that I just noticed I need to repair the front right fork as its leaking. I kinda dont wanna do it cause the parts are hard to find but it doesnt look that hard after watching this video........

Did this one time for water pump replacement.not as hard as I thought it was gonna be....but I did forget the shaft so I had to re drop it....only cost me 15 min more

Wish mine was this easy… mallet doesn’t budge them and I don’t have an impact. Do I have any other options or am I stuck with the old blades for the rest of my life?

What about the base? The grey part. Was that bought or built?