Відео

This year I got a pool liner for a 24' round pool. Last year we used a water proof trap, but it constantly leaked, and the sand washed out from the one side. The pool liner is around $499 from pool supplies canada. The liner wasn't much more then the trap I got last year.

The total price for the pool was around $3500, that's with the pump, sand filter, all the hose and fittings, liner, solar cover, chains and boomer, straps and rachet straps, foam insulation, and few odds and ends needed. The pool kit we priced out was around $7000, this way was half price. The pallets I got them from my work so they where free. The wood boiler was about $1000 to build, stove kit from amazon, 3/4" copper tuning.

It can produce upto 19 megawatts, thats like 19 homes.

I'm seeing over 8'c lower on the gpu and 5 to 6'c lower on the cpu. When gaming on performance mode, the fans are running 60% to 70% speed now in stead of 80% + most of the time.

@@trevork4066 ok thanks then there is something wrong with my paste job getting lower than average Cinebench r23 scores and the cpu is only pulling 70 watts in performance mode.

Thank you,!!

Thank you!!!

I went off my 3rd function line and hooked up a gauge.

The congen is mostly for heat, we send the extra power to the grid.

I ordered it from the dealer I got my tractor from.

Thank you.

It does, it just mine has something wrong with it so it's turned off.

Yeah sorry about that, but the front camera is the only one that takes good pics on my cell phone at the moment, one day I'll get a new one 😆

I now the recommended amount is 80 ml but 70% water fill is 90 ml. Most boilers are designed to run between 50% to 70% full of water. I rub the track both ways because I run R1 and R3 track and the wheel flanges do get wear after while.

@@trevork4066 Whats R1 & R3 Track?

@@PatSeba84 2 foot and 3 foot radius turns

@@trevork4066 ahh smart

I don't have any oak on my property, just popular and a few willows.

If it's that diameter and oak, it's firewood! This looks fairly impressive to me for that little chipper and tractor. This isn't a tree service chipper, the 6" opening is really more for being able to squeeze branches in, one primary reason I would rather buy the wc88 or other 8" capable machine.

No problem!!

Yes it is, I have a servo for the throttle and one for the reverser.

Well solar turbine generation exists, thousands of mirrors are arranged in a way to reflect the sun into a central point, this central point is that boiler which boils water into steam to run the turbines.

its ok for a turboshaft heli engine

The generator is on the cold side, there's a heat exchanger on the exhaust for plant heat.

Correct, single shaft engine with generator is on the compressor inlet side and there reduction gearbox between the compressor inlet and drive side of the generator.

Single shaft makes sense in a turbine that runs at constant speed and steady load, and this one is a single shaft design. But there are engines with two shafts that drive from the cold end. The shafts are concentric. Aircraft turbo fan engines all run that way, and many helicopter engines.

I have worked on many solar turbines, and it varies depending on how the customer configures the package, I have seen the driven unit on the inlet and exhaust side.

Dinosaurs. LoL

fermented

Methane

LNG, LPG, or Methane.

It's new, when I took the video it had 30 hours on it.

I haven't had any problems my self using the loader on my B2601, I do push the limits of my tractor on what it can lift.

For my Ruby, if I haven't run it for a while. I oil all the running gear and roll it over by hand. I rinse the boil with water. It's good to go after that.

We have lots of them here.

The one I have still runs, my kids are a little hard on it though.

LUYED 2 x 900Lumens Super Bright 1156 3014 78-EX Chipsets 1156 1141 1003 7506 LED Bulbs Used for Back Up Reverse Lights,Brake Lights,Tail Lights,Rv Lights,Xenon White a.co/d/6QQYUFc

I'm not sure, I did a quick search and didn't find any replacement screens, since Dell is still building these laptops, you might have to go though them.

This winter I got a set of rear chains for my B2601, I run one front chain too.

I used two Timetec 32GB KIT(2x16GB) DDR4 3200MHz (DDR4-3200) PC4-25600 Non-ECC Unbuffered 1.2V CL22 2Rx8 Dual Rank 260 Pin

The chain is a (Stihl 63 PS3 55)

They are soldered to the mother board on this laptop, the only way to replace them is to get a new mother board.

Ruby is getting a work out, she was running for about 7 hours.

@@trevork4066 that’s great! I have never run an engine that long before. Four hours was my max

@@Terrys-Steam-and-Cobi I add another 5 hours on it today too.

@@trevork4066 sign of a good engine.

I plan to take off the saddle tanks, I have some cnc wood to take its place. I run a tender with my Ruby and keep the battery pack in it. But free time with 4 kids doesn't come easily so its on the get around to it list.

I put it together quite quick, my wife and kids really like it. If I had more time I'd add more finer details and add more scale scenery. Next year if that have the hobby show a aging I'll add to it. I might take the ho scale train table out and run this one in the hobby room for a bit too. My youngest likes thr big trains over the small ones.

It's a Kubota B2601.

@@trevork4066 thanks!

I'm about 99% sure they are Bobcat branded chains. 12x16.5 is the rear tire size of the B2601 witch is the same for lots of skid steers.

I've had mine for almost a year, and it's not let me down yet.

Same here 1 year with rtx3060 model but with ryzen 7 i even upgrade the ssd to 32gb of ram and extra 1Tera ssd. Atm you can play games like cod mw2 on 120hz in high graphics or 144hz with medium with dlss performance mode.

@@gamecamacos why would you even buy a laptop without integrated graphics. thats so awkwardly backwards. lol.

@@typerightseesight ? The laptop has integrated graphics to use it on laptop mode? That save battery, The nvidia graphic dedicated card its to play demanding games, if its used to play without ac adapter with dedicated graphics the performance decrease a lot and the laptop waste the battery in minutes.

@@gamecamacos yeh, i know. but beyond that, its an awesome build for a secondary monitor. which works because technically you need extra peripherals to game on it anyway. the latency of the keyboard isnt 1000hz like gaming keyboards are. as far as I know all laptops are 125hz. at the keyboard.

Where I live the only hard wood on my acreage is poplar.

I save time by only doing the ones that are too hard for the axe

Good enough for the wife and her new favorite hobby .