Відео

Thank you for sharing the video, friend. His skills are extraordinary

Can't hear you with the music in the background

This video was actually a lot of help man I couldn’t get the power steering solenoid off until now

Good work 💪

That's not a Q50

How do you fix rhe low compression on that cylinder?

Where is the temp sensor located?

He forgot to put the oil filter back on in myvideo 😳

It's crazy I knew the botton was for something but never pushed it nore turned it and I had my truck for 2 years now 😅😅😅 problem solved Smh I was like why is my truck idling so dam Hight must of turned it getting out of my truck by mistake 😅😅😅Thank You

i tried moving knob still high

How the hell did you get them unstuck at 0:39 I've been trying to get them loose for days now

My Q50 give me the same issue, I already changed all those things my question is my car is half tank of 89 just add the premium in it

Brake pad sensor?!!! How to install it!!!

Did you reuse all the gaskets?

Could it still be fuel pump if brake clean doesnt work? I dont hear the fuel pump when turning the key

Tremendo video brother me ayudo mucho gracias!

Bullstit video

COULD A MULTIPLE CYLINDER MISFIRE BE CAUSED BY YOUR FUEL INJECTORS?

Hey please hwlp

Could you share the link to buy the tool to tighten the fuel pump cover, please?

Thank you for this video. I'm due for this again, good reminder of how much of a pain in the a** it was the first time I did it lol

Where did you get the part from?

My wifes Toyota avalon got flooded and I cannot crank manually the engine its hydralocked or; seized. After vacuming out all the water with a shop vack out the spark plug ports the crank began to rotate. Then my buddy crank started. Water burped out the intak ports. The the engine siezed again. I got lube settin in on the pistons through the spark plug ports. If saturdat results the engine still being sieved I need to swap the engine.

Thank you solved one of my problems

Is there a way to leave the AC system undisturbed and still pull the motor? I did that on another car of mine.

How long did it take to remove manifold

Great video

@ventura Auto tech you mess the strom other side from cable and it comes 12 V but you change the the other side with no cable on the Top,its correct ?? I have the Problem that co 12 v coming to the green/black cable, so i look FUse is ok Relai is full ok -its in back trunk of the car left side SAM rear Nr4 20A is the fus and Relai is A black one 20A, what is the Problem cable or the connection to the SAM or the SAM is deffekt,but when sam deffect why only Pump line ?

What ab the soldered connection that lets the car know the brakes are wore down?

The same

dude you’re a hack

Thank you. 2004 Lexus LS430, with lots of shudder or vibration when braking. I changed front brakes, and that helped a little, but only removed the vibration in the steering wheel. I learned when the vibration is felt all over the car, its probably the rear brake rotors. Your video walked me through it, and I was able to complete the rear brakes in minimal amount of time. The car is braking nice and smooth now.

What is the torque on everything?

Hey man thanks for the video it’s nice to know the rear piston doesn’t screw in because of the drum e brakes, easy to do probably don’t have to take off the caliper I don’t for my Taco. I just pry against the rotor too but I have a brake piston pry tool for bicycles that works better than a screwdriver with no sharp edges

was it the injector?

im having this misfire…. i jus checked spark plugs and coils even replaced the spark plugs and 1 coil

Thank you very much ventura...I got it now! YOU TUBE is the 💣

Bro you down bad for letting that caliper hang in da wind

Why and what are you removing?

Very helpful thank you 🤗

y otra duda que código de error tenía ese auto para revisar el sensor de gasolina?

tengo un problema con Scion xd 2008 en el tablero , marca todo pero la gasolina no la mide .. alguien sabe que se puede hacer ?

OMG 2:50 криворук

Pry against the old rotor not the new one and put lube on back of brake pads

How do you test the connector?

Great trouble shooting of the problem! Does this car have a fuel filter somewhere too? (2008)

How did you get the car to start with brake clean and how did you get the fuel line off I’m having trouble with the clip to see if I have fuel coming through or not

Thank you great video I am going to end up doing this for my vehicle thanks a lot for the information good job👍

HF! What a PIA just to install spark plugs.. great video, wish it were easier.

This is interesting because I’m going through the same thing. I changed all spark plugs, coil packs, and injectors. I even replaced the valve cover. P0306 code went away but I still am dealing with p0300. Note: I am tuned for (e85). But I’m still using stock fuel pump. I have a aftermarket fuel pump but I have not installed it yet. Do you think that is the reason for random misfire?