Відео

@@JokkazArt west biking

@@troymelandri1731 well i wasnt RIDING it to put into GEAR but yeah it works or else it wouldnt show the 0 which is the neutral gear

@@troymelandri1731 check your HARNESS for voltage your connecting to. And remember it wont turn on UNTIL u crank the bike up

@@TheArmorersChannel the indicator you purchase has a FEMALE connection that plugs into the MALE connection of your bike. If you dont have the housing but just the wires u have to use the DIAGRAM they include to make the correct connections. Black is always GROUND red always POWER so that leaves the OTHER wire that can only go 1 place.

@@stunnamrsports Thanks brother! I didn't know if I needed to unplug something or splice something to make it work. Thanks for the info!

@@calvintanner7897 prolly a PHONE holder perhaps with webbing. I dont have any issues with securement on mine.

@@kamsankowski6341 yeah u have to BURP the radiator. You can do that by way of the cap using a funnel. The SAME way you would on your CAR. just keep pouring coolant in it til it tops off in the funnel where it will BUBBLE UP. This while the engine is RUNNING of course. Once the bubbling stops your good. Thanks for watching.

@@glennspringer7420 REWATCH the video.

Ebay. I dont remember exactly who but as long as its OEM seller then your good.

No i hadn't been back. Once was ENOUGH for me considering how challenging it was maneuvering through the channels to reach the main river outlet. I have passed by and noticed its still a relatively unknown unpopular LAUNCHING POINT. I would recommend anyone to use it but be PREPARED for alot of hand paddling. Jacksonville doesn't really get alot of rain so i would assume the water remains low level there.

@@stunnamrsports Yea that is my main concern, getting stuck out there during low tide. I usually launch at Wayne B Stevens or Curtis Lee boat ramp. Trying to find something new in the area.

@@NoFro-TL i hear ya. Green Cove Springs have a nice lauch spot right next to the marina at the border entering the city. The water cops make their PRESENCE KNOWN quite a bit there so just make sure your permits and all licenses are valid. I believe i did a short video on it years ago. Lastly check out my video on Vilano Beach right next to st augustine. During the week its near empty year round if you like tranquility. Thanks for watching

Id imagine you could slide a screwdriver in that hole to keep it lined up while cranking the new hub on and not worrying about breaking the plastic sensor.

@@TheDylanjduncan FACTs thats eventually what i did 😂

Half a year ago, I went to a nearby auto repair shop to replace the left rear bearing and listened to the technician's complaints and roars for three hours.

Amazon or Ebay i believe. ONLY about $25 also.

I wish i could answer that but i haven't driven it since installing the axles. Its my PROJECT vehicle at the moment. The axle i put in was OEM so hopefully i wont have that issue. If i were you i would RECHECK your work and make sure u added the correct amount of trans fluid. U could also put it on a lift at a shop run up the RPMs to see whats going on underneath. Or just get a DYNO TEST done. Thanks for watching. 💯

Idk about that GEN but knowing Lexus its in the SAME spot. Either way crankshaft sensors are always NEAR the starter. Good luck

Idk i never had to take it OFF. I would IMAGINE it cant be that difficult MOST sensors are plug and play harnesses.

How much did you pay for the ignition coils?

@@raulgarcia9767 i paid ON SALE about $80 - $90 bucks PER coil off Amazon. They are now $100 per

@@stunnamrsportsthanks

Yeah if i find some i LIKE. The ones that fit aren't my STYLE

2014

you have to drain all the freon out of the system. I have a video for that on my channel.

@@stunnamrsports tight. I didn't see it

You don’t gotta disconnect non of that shit bro

@@Rxdomowhat you gotta do ?

Did u watch the ENTIRE vid? Its definitely been SUBMERGED 😂

@@stunnamrsports they took the Raptor experience to a whole new level, lol

No issues HERE. Im not sure what PART your talking about. I would just keep researching and go back over your work. Walk AWAY for a few hours or a day then come back. Sometimes fatigue CLOUDs our judgements and decisions. And it helps to RECORD your uninstall for future REFERENCE. Thanks for watching good luck let me know how it turns out.

I think he bypassed having to fool with that ring by leaving that rear piece in (hence the Allen wrench bit). I hope the 2016 (is200t) is the same. There’s a dude on a different channel who had to take a ton more stuff apart in a 2017 but I think your trick was a work around to all that. He had to spend $190 to have Lexus install a new ring since he destroyed his. I have to replace my wife’s right rear on her 2016 asap

@@76marcpalerminohow did that go? Did u have issues with the dust ring?

@@kalieburrows1427 No. No issues at all. You don’t have to take the dust ring out.

@@76marcpalermino yea I got it in just have to make sure the hole stays lined up… the ring get pressed between the axle coming out when torquing axle nut and inwardly when the hub is torqued… nice n easy 👍 That one guy who disassembled the whole knuckle has the entire internet weary of this job lol

Glad i could HELP

Regarding WHAT

Lol. Yeah i really need to STOP. Its making me car POOR. 😔 thanks for the support bro. 💯

I had to do THIS for an stx I had. Triton ENGINE I believe. So u can at least give it a TRY

I got the replacement in last night, about tobdo the installation now, but quick question. Did you disconnect the battery at all?

@@DonBorgia ALWAYS disconnect the battery doing anything ELECTRICAL. 💯

So I followed and got the installed and complete. I got power keys and alarm work, but no start. All the components match up. Anything

Thanks

Idk. I had a ford stx but NEVER had this ISSUE. But knowing Ford I wouldn't doubt it

Sounds like a clearance issue. Are the shocks adjustable? Do u have a lift kit on it

@@stunnamrsports had to remove the strut good now

Right RIGHT👊

It's doing it's JOB. No issues thus far🤘

@@stunnamrsports that's what's up then good looking

Yeah it was the AFTERMARKET clutch I added. I just put the FACTORY one back on. It workS😁

Appreciated 🤘🏼