Відео

I bought a four pin right off the best years ago. Awesome crimps. They only issue i have is I get some that wrinkle. Mostly Winchester 10 gauge hulls. Don’t know if sis t have enough lube or they are just weak hulls? Remington and federal roll great. Chedite normally does ok but I need a lot of vasoline applied with a Qtip in my crimper.

Three of the Steel loads at 100 looked like they weren't stabilized and went thru sideways. Love your content.

Shotgun Hulls

What do you use for wads for your slugs

13.:46 "Fast lead wide spread, slow lead kills dead" 🌶

Really cool press. Been reloading for nearly two decades and never come across one of those.

I solved ALL my foster slug problems by going to the Lyman .705" 475gr slug. Unsurpassed accuracy even at 100 yds.

Found you....subscribed now.

Sorry if I missed it, but were all loaded with 18 grains?

Apparently they’ve been discontinued.

Went to the reloaders network site to buy a 12 ga. quad pin crimper, no longer avaliable whats up. ?

The beard 👍

I’m thinking of putting this on a home defense shotgun so I don’t have to rely on hard to get buckshot like Flight Control. Would you have to remove this to shoot slugs? Fantastic video. Thanks.

Upvoted Brother. Subscribed, bell rung, commented, upvoted, liked, shared .... may the algorithm gods smile favorably upon your channel. Keep preparing for what is comings, where the evil democrats are taking us. We will win this thing.

Kinda man-handled (didn't wait for it to heat up a lil bit) the BPI crimped shell, but still make an okay crimp. 👍

Seems like the factory full choke may be just as good imo

Just catching a few of your videos on lunch after a couple weeks of BRO & Shotgun Scientist. Look for to more videos. 👍

Have heard your FB group recommended on another shotshell reloading group. Didn't know you had a YT channel. 👍 Hadn't heard that saying @13:45. Good to know.

I see you have powder migration not good

Nice video and resourcefulness! Thank you! You didn't have to call your son out like that about the camera, though. I'll assume you were messing with him. 😂

I just reloaded my first 410 000buck loads. I used a ballistic products roll crimper and attempted to roll crimp them. Theh did not look super pretty and the top of the crimp was more flat then roynded over. They fit in the gun ok. Well see if they print worth a damm at 15 yards or so. Wish me luck.

Awesome lil'loads man

Take drive key out tiy mold shut weat sandpaper spin mold on finger. I was working on turkey loud 20 Ga. Hall yes it fits in 12 Ga. Hall crimp up & down cont spread at 50 yards.

Thank you for sharing, very interesting. Best ballistic test ever.

Hi. Love your video. Just got a 590 Shockwave and very interested in loading short shells. Which model of roll crimper do you use? Did you get it from BPI? I just found their website and they had more choices than I expected. I'll just be using it for shorty 12 ga. Thanks.

Excellent video! Thank you

Rectifire is actually just up the road from me in Allendale S.C.

I have a kicks xtra full for #1 and 4 ...but honestly my patternmaster code black duck NEVER comes out my benelli...that gun /choke just works from my dove loads to duck to buck...it loves cheap federal powershok 15 pellet 00 all 15 everytime...also will throw all 10 federal premium copper coated 000 in a pie plate at 50 yrds...i like that i know how my gun shoots everytime instead of having to change up chokes...gotta put in the time like you have and PATTERN your gun...find what it likes stock up and dont change.

I'm guessing you could use the gas seal cut from a regular shot wad in place if the actual BP gas seal? Have you pressure tested these by chance. Curious to know how the pressure runs. Thanks.

Are you a Marine if so SEMPER FI ,ARINE AND THANK YOU. An old Army MP vet here.

Graphite is also used by locksmiths.

thanks good work we needed this

Are these wads still attainable? Thanks.

How you cast your slugs so shiny? I use pure lead for my slugs and they are kinda dull grey

How do these do in a Remington 870? I noticed your overall length is slightly longer which a 870 would prefer

6 pellets 00 is 0.645ounce 21 pellets #4 is 0.99 ounce 20 pellets #4 is 0.94 ounce For 1¾" shells you will run out of room with plastic gas seals and buckshot. I use cardboard over powder, no wad and just 20#4 pellets. ⅞ounce slugs I use x12x and part of a spacer wad wrap slug in part of the trimming 0.690 RB BPGS wrap in trimming.

Hello, i could use a bit of help. Im shooting a Remington 1100 with a 22inch slug barrel with rifles sights. It a smooth bore with what im assuming is a cylinder bore choke. Im using AA gray 2.75 hulls and claybuster 1138-12 wad and hornady OO buck. This is for defensive proposes and im patterning for 15 yards. My goal is a tight 6-8 inch pattern. Ive tried blue dot, red dot and longshot powders but my patterns just wont geg to where i need them to be. Dont get me wrong the loads ive tried worked fine but are giving me 10 inch or slightly more at 15 yards and keeping most shot on a human torso target. Unfortunalty there were some questionable fliers that i cant have. I have used 9 pellets as well as 8 pellets. I have used the full wad and also cut the pedals off. Ive tried buffer and no buffer. All this changed the patterns slightly but not enough. Do have any thkughs on how i can tighten things up to where i need them.

Can I shot slugs if needed sometime not always with light full choke kick ?

I like this rounds for the ranch for black bear protection.

I hope you redo this video sometime. Good info but your camera skills and microphone sound sucked.

I made one out if a socket and a car boty bolt and nut then used a grinder to take the 6 point off then bolt all together and then put a pin or not me no pin. i go off heat. One question how come people put so long of screw 🪛 on the slug to wad. I guess see this alot. Dont you want the wad to crush. because i see it mostly don't crush with so ling of screws that go throw hafe ways though the wad. I just thought 💭 what I've been seeing on video's.

Sick m8. Tuning in from the UK

That was informative. Thank you.

Leon, Thor's Axe here, (Friend of Jeff and Fortunecookie)... first time watching and I like what I see, keep up the great content Man, Peace out Brother. - Dave

You're helping many and I thank you for that.

Can someone please explain how the plastic part is ‘fused’ to the brass base? It seems like there is a lot of ‘excess plastic at the base where the brass is. When looking at plastic hull extruding machines, the end product is cut to length, does this mean at the brass end the plastic hull is scrounged up in the press to create that plastic mass at the base? No glue is used to ‘stick’ plastic to the brass right?

what about recoil? does this things reduce recoils?

👍

100% with you on the wood stocks.

Is this only good for loading virgin hulls with primers? No way to decap, resize, or prime previously fired hulls?