Відео

Haha nice

I just bought a gehl 2600 off a guy for $200. He said the original 25hp Onan gas job was running like crap and he just wants it off his property. Its in good shape, needs a little TLC, but my idea was to throw this engine in there and just use its around the farm here and there. Problem is, you made it look way too easy lol. Looks like im going to attempt it now.

I just got these and they came with no instructions. thank you my friend for helping me out!

You never put the exhaust pipe out of the engine compartment and it sounds like it should be revved up hhigher when operating it

There yeah go 400 h.p. added already.😂😂😂😂😂

I have the same one, and im thinking the same thing

See if you can get some of Dusty’s stickers?

The predator has its own vacuum fuel pump already

another con is if the chain breaks you have no brakes

Tat is the smartest thing I have ever seen on utube. Thank u

you put a volt reducer? I mean the toy use a 7.4 V I think and the batteries are 12 V

Seems like a pretty well grounded guy

Please? What is the distance between the two rollers for each steel tube and its diameter?❤

I wonder if that intake valve got swapped out at some point considering they have different clips

What size band is that?

You did a good thing here for this old tool gambler that rolled the dice on the same unit. Very helpful. Thank you.

Thanks for the video, I might have missed you mentioning this but why not have rubber isolators on the engine mounts?

I made a comment a week ago, and then the bottle jack failed. It has barely been used, but when pumping the handle, the piston would raise and lower in rhythm with the jacking action, so the relief valve was not seating. I took the jack apart to clean, and the oil was very contaminated. It has barely been used. After a cleaning and fresh oil, it is working again. Unscrewing the center tubing took a 3 foot long pipe wrench plus a 3 foot pipe extension, and a lot of force. I also had to re-anchor the bench vice.

Cool dude, I took you're advice & getting better results. I'm under the impression that it's the sides that benefit from support as the roof of the jig does not even touch the tube after a bend.

One of the best tips I have seen for this contraption. I am also making a conversion tool to bend 14 gauge sheet metal for brackets, braces and custom fabrication, since I do not need or want a press.

Epic! I also did a lithium ion conversion with one of these, but I used a 24v battery. I’ve been thinking about upgrading and have been wondering the same thing: would a higher voltage battery damage the motor/controller? Would love an update to see how your build Is doing under a longer test!

That's what I call a lawn mower ! 😂👍🍺

I just removed my locked up CCKB 20hp Onan from my 444 bobcat. It locked up because the previous owner blocked an oil passage with gasket maker. (I just released a video today of it running again). I don't intend on putting it back. I'm going the 670 predator route also. Thank you for the key switch information! Doc Martin

I thought it was alternators that charge the battery?

Make that another subscriber he did a very good job but I got to ask him one question hey buddy what are you doing with that old motorcycle sitting on the wall

You should check the temp of the spot welder board, some boards get very hot.

Did you ever finish this? Did the transaxle survive the RPM and HP?

Sir you just earned another subscriber. This shows proof of concept with a minimum about of fabrication. You got it all running and driving. Would like to see some long term follow up to see how well the pairing is holding up.

WOW! What a nice job. Thank you for the video.

I'm pretty sure that the heat shrink was for the pens. It was good to see that you didn't have a bad experience holding the bare ends of battery cables.

Weird. I didnt hear any feedback. Great video and project. Would love to seeit in the summer to see what it can do.

I like the video. But the sound feed back is making hard to watch. Keep up the good work,

Thanks. I'll give that a try.

Is this for sale?

Hey what happened on the flat head Ford John Deere tractor build? I am looking forward to seeing you complete it. Love watching all your vids :)

Those old Wheel Horses are so good looking, in my opinion of course. Nice job on the re power, it just got a whole new life! Enjoyed the video, thanks for posting!

I usually put old nuts and bolts in them and shake. Works. Legit idea.

The plastic XY insert is the Atari Joystick's weak point. It breaks too easily. Come up with a more solid replacement and everyone will buy that part.

I dig this, fun to do so your playing all original though i favor the sega genesis controller, it is the best of control pad controllers, way better then nes and it has the pin or whatever count that fits colecovision, atari, commodore & all old school systems (:

Nice

Tienen que ponerle diferencial ,es difícil maniobrarla asi

Gonna bring that hotrod to the threshing show?

Prob could be a wood chipper too

Yes it would be cool

Sounds good.

I feel your pain from Alaska

Solid

Mantap bang 👍🙂

Great tip! Thanks

What is that thing he’s on? It has head lights?