Відео

Awesome! Looks so much better!

Put on a ditching bucket you'll be twice as fast as the tractor

I just did a blown head gasket on HHR with bluedevel followed all the instructions and just pasted 1000 miles and no sign of sny issues.

[ thank, you for youre video. nice, looking dump truck. I, own a 1973, Ford F-700 361 engine. 5-spd. manuel trans. 2-spd. rear axle. air brakes]

Super helpful! Thanks brother!

Great video thank you Sir

How have these bushings hold up so far? Contemplating going with them vs bobcat.

Corbin? KY?

Man you have some stones posting videos of your welds! Every “pro welder” out there is going to have something to say! It looks good to me tho man bout to weld one up to my uncles excavator that’s why I looked it up. If it looks close to as good as yours I’ll be happy!

Great video. Way better than doing it with my mini skid and bucket😂 Thanks man.

My fuse keeps blowing out has yours?

yep just like mine lol. she gets a little grumpy gotta plug it in around that temp. only downside to the older diesels

Blue is Sky⬆️ Brown is down⬇️ Thank you sir

Are you using gas ?

You just convinced me me which one to buy!

How is it with cutting stainless steel like 3 inch exhaust 18 gauge

You need a 75 degree to dump in 1 big pyle.

Can I please get help. I’ve watched so many videos. Do what every one says. I’ve tried two different remotes. I can’t get mine to work

I watched another video where they talk about diodes being used so they don’t backfeed the power into the original remote. Idk much about electrical but might be worth looking into

This helped a lot…. Identical to my pump and solenoid setup… I bought my trailer back in the spring and picked up one of the Amazon controllers but never got around to installing it till today. I just happened to watch this video as it was a recommended video. Hooked up the controller and everything works great … thanks for making this video… I would have figured it out but you definitely saved me a few mins

I rewired my Z completely, lot of work but worth it. I did install a modern radio but I hardly ever listen to it because the scream of triple webers just sounds so good

Nice work

How much do you think just the canopy weighs , NOT including the underneith frame work ?

Do you have a video on the engine oil change procedure for the Bobcat E26?

Awesome video buddy thanks. What would a dp21 2500 hours be worth? In good shape

My 7.3 has 700,000 love the motor

k...your the cause of climate change..ask trudeau

Love my seven three

Is soldering and welding similar ? If I can do one , can I do the other ?

Never seen someone start a torch like that, never doing anything else

This is the video I needed. Mine has been cutting at a slight angle lately. I do wish the one blade guide post was longer, because you want the blade guides to be as close as possible to the material.

Did you fix it?

Blade must be sharp and cutting rate must be not very fast.

Which holly carburetor is that

Idola gua

hows finding parts for these?

Wireless remote still working well on the dump trailer?

Thank you man! Out of the 5 videos I watched yours helped me understand how to wire it and realize how simple it is to do. It helps we have the same trailer too!

Like you said, longer sanding block, I forget the terminology but spraying a light coat of paint then block sanding will show you low spots to help smooth it out. But also I’ve found that you will always be the biggest critic of the body work especially if it isn’t a show truck. So as long as you’re happy with it and no one else can tell, who cares?

What’s the benefit of the glass?

Lol welding rusted up aluminum! I’ve seen people try to weld sheet aluminum to steel, it’s not pretty

That bump at the end of the video might have been from too much heat. It was hard to tell if you were laying a bead or doing a ton of spot welds. Should be doing a ton of spot welds and bouncing around. I’ve even seen guys doing a spot weld then cooling it with a blast of air from the compressor

For some reason, UA-cam didn’t let me know you were posting videos. Now I need to catch up!

What size is your dump trailer

If you dump a lot that day, your battery will need help n hook up a booster pack to help max out the power of the pump

Thanks for this video. Just what I need. Recently picked up a 2019 7x12 12k Cam Advantage Dump second hand and have been thinking about doing similar modifications and am asking for clarification of what you did to get past your initial fitment issues on the Rear stabilizer steel. I was thinking about using 3"x1-1/2x3/16" tube for the main drop leg forward (as pin placement should force jack pivot force forward) and 1-1/2"x3/4" x11ga steel tube in rear as both a filler and possibly as a fixed wiring channel for possible addition of a stake pocket combination tail light/extenstion 12" board bracket similar to what you would see on a Sure Trac or Griffin as I sort of like that style setup and think brackets along those lines would be much more sturdy. Realize I will have some spacing issues with the tail light against the rear door upper latch which would force me to push the 2" tail light tube inboard a bit but I ought to be able to center up on the extension board bracket side of it without issue and wanted to hear your thoughts on that too. My real concern is the fitment using a full 1-1/2x3/4" channel vs your much smaller 3/4" square tube. Also interested in what you used for overall height and pin hole spacing on this as well. Appreciate any advice & specs you used you can give. Thanks.

Congratulations!!!🍻

Hold on! We gotta wait a few years for the kid to confirm to know for sure. 😂 Congratulations 👏

I’m thinking about buying one of these for 10k just trying to make sure that’s a good price. It seems to be

Heck yea your set now