Відео

I put a 3” and I don’t notice any of this happening also alignment isn’t the kits fault you have to get it aligned after done

The higher they go n front the worse the mileage. It was designed and wind tunneled lower n front, just that lil bit will mess it all up!!! Any change to tires or suspension you gotta get an alignment bro.

Link for the housing lights please

Why cant i just premix even if my oil injectiom workks

Merry Christmas bro hope all is good 🙏

So glad ford charged me less for my truck and saved money on the drain plug for the diffs and tranny.

The fact that block is plastic should have been a clear reason to refund.

Do not do this to your piston!

Great video! I do have the same engine but in the Ford edge. Got my part off of Amazon . Thank goodness I didn't go to the dealership because I do own a code reader but that is bananas that they would even charge that much

Improper break in. guarantee it 😂

Alignment you also need to look at your suspension components as well

Thank you for the bit about the code clearing. Dozens of videos and this short gave me the answer

Wait I'm so confused. You leveled and didn't align and your mpg went up. Wtf. 😆

I enjoy sooooo much how much he uses M….. F…..!!!!! God Bless you Chief Goggins!!!!!❤️🇺🇸❤️🇺🇸❤️🇺🇸

I have one that is stuck turned on and i dont see any wires or plugs powering it. When i bought it was off. Today it randomly turned on and wont turn off. Any tips?

Awesome - knowledge gap filled!!

Do you have. 2.7 or 3.5?

Cool quad man but try rejetting the bike or doing a leak down test instead of taking off the exhaust system especially on the blaster because those fmf systems make a big difference

How long have it lifted now? Any trouble with the struts, cv joints, driving comfort?

Need pounder music

600-900 is complete robbery for this

Get the upgraded aluminum pan ASAP I promise u this one will leak no matter how many times it’s replaced

I have a 2.7 F-150. The hard part is removing the panel under the Engine, and the oil comes out like a garden hose. The filter is really easy.

Muchas gracias amigo! Tu video me ayudó mucho

Dude, youre supposed to get an alignment after installing a level kit 😅😅, u really didnt know?

Hey did you mount the power box in roof ?

How u get it out the truck 🤣

Wtf

Brro im dead lmfao reminds me of some of my lennox bois

I was about to say, hold on I think your damaging it 😂, then realized at the end 😭

Can't finish the video and actually show what is wrong??????

You should put some water down there to sit and wait for the next drainage of oil. They will call for you again😉

When your a subcontractor than needs to subcontract another contractor 😅😂😂😂😂

So you did a crap nitrogen test and a crap vacuum. Good job

I hope you put some clear silicon around your new light. Just to be on the safe side from leaking water into your headliner.

That filter dryer welding 🔥🔥🔥

You anywhere near Ohio if so I’ll buy it

Lmao 😂

Ayo, audio/editing on your videos is gettinf better 🔥 nice back lights bro

Attics suck bro, what did it end up being?

Easy money

🔥🔥🔥

Hell ya easy money 🔥

I knew a guy who stocked up on engine oil back in 2020 when a autozone gpt lotted on his block lol.

Badass🇲🇽🫡

I’m a big supporter bro can you take me with you one day

Sheesh 🔥🔥🔥🔥

Work hard, play hard 🔥🔥

😮

This is why I always check I work in an industrial setting and you’d be surprised what I have seen. Just recently had to fix 4 fans being tapped into 60 amp fuses that is a disconnect for a 250 foot 60 inch wide chain driven belt. The wires started to short out in the wire nut and melted all the insulation back to the disconnect absolutely stunning. Also know a guy who recently was killed in zues because someone by passed a main disconnect and he wasn’t aware moral of the story here is people do sh*t like this all the time so you can’t be too safe!