Відео

Which one you want yo use?

TowerPro SG 90 Micro Servo Motor

Yes

Tq❤

5v to positive, GND to GND of servo to Arduino board and signal wire to A4 of the board Check it in Circuit Diagram: drive.google.com/file/d/1bFK8Dwt6g-Z2kP-Qzci0NTRzXW0DrkRT/view?usp=drivesdk

@@saadinnovativeideas bro but in video you connect all 3 pins to the board

Yes, should be

@@saadinnovativeideas 7:15 you connect all the pins of the servo to breadboard is it right????? in the video

@@saadinnovativeideas and in the circuit diagram you have connected the flame sensors wire to the arduino board but in video to breadboard which is right???

Your power is not enough. What is your total input voltage

I don't no

Jo apne use kari hai vo hi use kari hai

Or micro servo bhi nhi chal rha hai

Sensor kitna pin wala use kia hai?

Yes, I think so and I may do it in future

Does other components work?

Laptop and computer. There is also a way to program it with phone

Thanks bro

I think so, try it

One

Did you succeed to connect it with phone?

Ya bro

Name the battery used and sensor pins

Did you mean its not uploading?

@@saadinnovativeideas Brother how to do the coding?And how to upload that coding?? please help😥😥😥

I have explained it in the video. Just copy the given code and paste it in Arduino IDE software, select right port (COM) and port and click on upload. Notice the Arduino board double blink

@@saadinnovativeideas Thank you soo much.

25-30$ for components

Try to use 4 pin flame sensor. If you fail to avail, then for 3 pin flame sensor having D0 pin; Connect A0 of all the sensors with 2,3,4 (digital) pins of the Arduino uno board and in *code* replace A0, A1,A2 with 2,3,4 respectively and replace *analogRead* with *digitalRead*

@saadinnovativeideas I tried it but it still doesn't work

Does leds, horn works

@@saadinnovativeideas i didnt used that

Do you succeed to connect it with phone using Bluetooth Car application

@@saadinnovativeideas yes

Send me the picture

25-30 $ for components

Since I am doing, less than a minute, usually 10 seconds

@@saadinnovativeideasit was taking too much time(4-5 mins) so i remove the cable and push red-button on uno for reset and then re-upload this code and this code giving error.

You may not have selected the right port (COM) or you cable may be faulty

@@saadinnovativeideas All thing is good but one major issue is my robot is not moving after detecting fire and some time it is giving long beep sound.

Yeah, you power supply is weak. Name the batteries and net input voltage

What type of explanation. Already fully explained in the video

Means fire is already detected

How can I help you?

Yes

I think I just figured it out. I didn't notice that I used 12V water pump which may cause the transistor to heat up fast

Of course brother 12 V pump will consume much amps causing the transistor to heat up

Can I ask, what if I use 12v water pump, what should I change in the value of transistor and the resistors or capacitor??

Name the pump, and if you can also tell its ampere consumption

25-30 $

Walikum Assalam, happy new year brother ❤️

Check you power supply

is the battery my problem? its 3.7v but 4000mAh in 2p

Yes you are having battery problem

3.7 v per cell is okay, but you said 2p means two batteries in parallel, means the total voltage will be again 3.7V which is definitely not sufficient and bo motors will not rotate. Connect both 3.7 cell in series making it *2S* so its voltage shall sum up to 7.4V which is desired.

@saadinnovativeideas bro i followed all the instructions you shown but when i uploaded the code the water pump,the flame sensors,the servo motor when i turn on the switch it automatic, detecting fire even theres no fire there. Whqt is the reason bro?how can i manage ?and also i followed the power supply but the wheels dindnt fuctioning.

Please help me 😢😢😢

@saadinnovativeideas help please 😢😢😢😢

Nahi bo motors mai positive negative consider nahi kia.. koi or ghalti ki hogi

5V pin of Arduino uno

@@saadinnovativeideas u have plugged it in breadboard?

DC 5-9 v

Search *Arduino IDE* in browser and go to download section, all versions are available

@saadinnovativeideas will the code work same in other versions or there will be issues

Yes, no issue but should be of Arduino IDE

Try to flip the bo motor wires connected with motor driver unless acts correct

Brother apply same connections as given in circuit diagram. Try this new clear one drive.google.com/file/d/1bFK8Dwt6g-Z2kP-Qzci0NTRzXW0DrkRT/view?usp=drivesdk

@@saadinnovativeideas saad bhai ..agar aapko time mile toh pls breadboard pe bhi connections laga ke image share kardo ..it will help newbies like me :)...btw happy new year ...i subscribed ur channel and also told my freinds to subscribe it ....boht accha kaam kar rahe ho bhai ...waiting for more projects by you :)

Thanks bhi for praise and efforts.. Lekin mene apko bataya ke bredboard pr bhi yahi connections krne hai simple hai bs circuit digram ko dek kr katlo

It really works brother, check your components and connections again

For components I spent 25-30 $