Відео

I LOVED your video❤ straight to the point no jokes

Nice i was going to purchase this. Thanks for the review. A video of you making the mods would be cool! 👍

I like your method! I really appreciate when someone carves their own forms (as opposed to using a 3d printer).

Did the thermocouple burn up yet? The 3kg crucible rubs on the thermocouple and leaves graphite behind on the tip. That will eventually burn though. I'd recommend using the 2gk crucible. As far as I'm concerned, vevor furnaces are garbage. I've purchased two of them before breaking down and spending 3 times the money for another furnace that heats up 3 times faster. The vivor also uses WAY MORE POWER then the higher quality furnaces. I run with a tabletop quickmelt furnace now and I can pour copper in 25 minutes from cold. If you're going to stick with the hobby, I'd highly recommend using a higher quality furnace.

Nice job. I'm looking at a pond that was a pool and is too much for my builtin sand filter system. Definitely going to give this a try

I think you need to cure it first with CO2 before applying heat.

but how does it tasted compared to drinking from plastic bottles/aluminium/ceramic?

Here's a video idea: Make a silver shot glass of Doc Holiday from Tombstone. A classic film will always get the fans to quickly tune into the video especially if you get the right thumbnail & video title (like Doc Holiday, Tombstone, Val Kilmer). Maybe you'll even get a fan to order that product afterwards. Also great work 👍

Just an idea, during the editing, you could add some voice over about why you do certain things in between segments

0:53 7 more subscribers in just a day

A jewelers lathe would be handy to replace all that hand filing. Amazon has one for less than $200.00 US Universal Mini Metal Lathe Machine Motorized Metalworking DIY Tool Benchtop Woodworking for Hobby Science Education Modelmaking W10003M AC100V~240V (24W Lathe). Subscribed - good luck Mike

Very interesting. Nice work. Don’t know anything about silver casting

Just found your channel and subscribed. Very nice work

So the cold start rattle from the VTC actuator does not cause any long term damage to the engine, it just annoying! Thank you for a great video!

Best to replace with Emerson Sure Switch. Amazon has good prices.

I’m building something like this out of spare parts. What I can’t figure out, can you backwash it? How?

It might feel heavy but its still light compared to gas .

Thank you for uploading this video. I started to build one . Got a pump and a used cartridge filter. Only problem I'm having is the exit pipe. Went to local pool store and they couldn't figure how you make it bend when you cleaning and straight up when finished. Any advice on the fittings. Thanks

The screen on mine isn't displaying anything. I'm guessing it's a wire problem but i am also not knowledgeable on these machines. Any suggestions?

Hello friend great work by the way . It turns out that calcium oxide converts back to calcium hydroxide , a deliquescent substance . I did not know this happens . When it converts from oxide to hydroxide it expands 75% . So it turns out its only good for a couple uses or maybe only a 1 time use heat shield . I have since bin suing zirconium oxide instead of lime . It makes a high emissivity paint that increases furnace performance . You can also make high temp glue with it

What is the micron rating of the filter?

Mike, The Honda service document shows torquing the cam and actuator out of the vehicle on the work bench. Given that, I don't see how the key pin on the end of the cam is out of the picture re: torque. I have not been able to get anyone to explain why it needs to be unlocked when torqued (especially if it is torqued out of the vehicle.

Did you try sand lime and waterglass? I am at the start of my build and really want to get it right first go.

Push the gas pedal down to the floor. This will shut off the fuel injectors and prevent your engine from starting. This will allow you to crank over your engine long enough to build up the oil pressure without your engine starting. Release your gas pedal after around 5-10 seconds or so (dependant on outside temp and engine condition) and your engine will start without the rattle or significantly less rattle because the oil pressure was given enough time has reached your VTC actuator.

5:26 That was one of the cleanest pours I've ever seen. Great video.

"i was drinking beer while i was doing this" i had to laugh because i know this kind of unprecision 😀

THANK YOU SO MUCH for this video and explanation!!! I've been going crazy trying to determine the source of that rattle and have heard all of the speculation surrounding it. From: 1. It's the timing chain rattling against the guide, about to jump a tooth because it's stretched. 2. The oil level is low, or the type of oil is insufficient. (Although I do recognize that oil plays a part). 3. It's the chain tensioner failing. I have had Honda mechanics swear that it was the timing chain making this noise, but I was never convinced of it. Now I have what I was searching for, thanks again.

Helpful video - Thanks! I'm sure you have found a lot of new info since you posted, like oxy-acetelene flame is about 6000 deg F (no firebrick will handle that), but that what ilearning is all about, right?

I simply need to learn how to weld now...

Please what size are those 5 point torx?

I like what u did buy when the folter fills up with water, can ypur cart support it ?

Walmart

5g tower right next to your brain when you sleep.😮

Thank you man. So what I have gathered is that it is annoying, but it doesn't cause any significant damage to the engine. The problem is, however, that the check engine light comes on in newer cars, which necessitates the changing of this ~$150 part (got a quote for over $700 at the honda dealership)

very good and informative video , thank you very much. Now the question is Why Honda is allowing this to happen in almost every model

Use a barbed 1 1/2 pvc fitting on the front of the pump for easier prime with no duck tape

The VTC controls the Intake Cam actuator angle.. whiles the Vtec Solenoid controls the engagement of the 3rd Cam lobes.. wanted to point that out its 2 different functions.

Hey uncle congrats on 300 subs i have 255 im catcging up

How is it working out for you, just purchased one

thats really cool. (the sodium silicate and sand) is it strong enough to build a cup out of to drink from or make a bowl?? or is it too water sensitive to hold water.

thanks for the vids they are really cool. u r excellent man.

I think that was the bottom just being a bit thin, or put it slightly higher temperature the mould as you pour it in, cause u could see it cracking a bit when u poured it in.

Bravo! Well done! Short and full of answers to questions we all had. Thank you.

I think there was no vent for gases to escape.

I got the same one does the same things. It’s crazy I couldn’t find any videos for my issue. Thank you for the help. Imma gonna try this asap 👍👍👍👍

Nice works the FOOT Pounds Please to tight?

We have a used 2012 Accord SE, exhibits a quick rattle(<5secs) from cold start. If we do religious oil changes with good quality oil, what would be the consequence if nothing is done and no CEL yet? Thx

alot of these videos NONE show how to assemble the floor... hmm

And the dealers do not sell you the spring but the entire gear at exuberant price!

Just replaced the spring on my 2014 Crv. Your explanation is awesome, I knew it's the weak spring but didnt know what it is doing.