Відео

Took optima apart 5 years ago and finally put it back together today with your help! Add in your description that this also works for early model optimas. This helped me out so much!! Thanks man

Sounds really windy.

Thank you! Wooden dowel got me there 😁

100yds?

I took mine apart probably 15 years ago. Been told by every gun smith that it can’t be done without me buying a special tool… can’t wait to try this.. thanks!

Thanks so much man I have a question, I followed all the steps and when it’s completed the trigger is not wanting to reset? Any ideas?

Thanks for the video

this video was saved me so much frustration and probably having to send it back to CVA. Thank you so much. Wish I could buy you a beer.

Well you saved my tail! I used a chunk of chainsaw file instead of a bolt. It popped right out no issues.

I made the mistake of taking my Wolf V1 apart, and this video saved me from sending it to CVA. Will never make that mistake again. Thanks!!

So glad i watched this video before i took my action apart. Any time i see pins and springs under tension in a blind spot im like, "nope". Brake cleaner it is lol. Ive been using birchwood casey gun scrubber with the little red straw. For as exposed as cva trigger assembly is to fouling, you would tging they would have made a better design like the seperate trigger assembly on tge old eclipse or something.

Which Gun is this for? I have a CVA Wolf but the trigger assembly does not look like this one. Mine has many more parts than this one.

Omg thank you so much. I am one those guys that has to break his gun all the way down. And I did it and went oooooh sh*t. Thank you

awesome video, thanks.

Always had the feeling aero coasted off of a fancy name and price tag for mid-low level products... this confirms it. Thank you!

Does anyone make a lighter spring kit for these?

Well, I took mine apart for absolutely no reason, then realized I made a mistake. Thanks for this video, I'm sure I would still be struggling otherwise

You should have used some heavier match grade ammo. The 1/7 twist is optimized to stabilize 75-77gr projectiles.

Thanks man who would have thought so much headache not very user friendly is it

I had an aero precision Ar and depending on your rate of twist that will change it a lot. Mine liked 70 grain barnes and it would stack them. You don't have your upper set up right and more than likely shooting a lighter grain for that rate of twist.

Great instructions thanks

thank you for this video got one in shop that was taken apart and owner didn.t. remember how it came apart, if you do many of these let me know as I am making a slave pin for this and 2 are as easy to make as one, Thank you again

You're a champion mate!! I would've been stuffed with out this video. Thanks from NZ

I just bought this gun, I’m around 500 rounds through it. No problems with standard target ammo cci and (Remington gold bullet). However I’ve tried 2 different self defense loads and had failure to feed with the federal punch, and even worse, failure to eject (had to pry out the brass) almost every round. I bought this as a multi use gun that I could start carrying, but it seems I can’t use self defense loads. Frustrating. And I haven’t seen anything but positive reviews, so wanted to share

Man are you kidding me? Wtf you can plug the m4 loader straight instead of the box, you don't need any adapter 😂😂😂 Try it and you will realize how useless is this adapter 😅

I've been a gunsmith for 36 years. You helped me from pulling my hair out. Thanks, David

That sure is a nice range...😁 It's nice to have a place to stretch out..

20m (65') bullet drop? Nice shots.

Just saw this., good video. Looks like the PSA is a bit more accurate and no issues....... I believe your under gassing issue can probably be fixed with a lighter spring wt or lighter buffer wt. But you will be switching them out everytime if you keep using the same lower....just my 2 cents.....

Should’ve got the psa lower too.

Success!! Great video to get me started and alignment of springs, pins, etc.

Try a small piece of wood dowl to hold the trigger spring and trigger.

So (appears) different barrel lengths, and different gas system lengths? How is this a manufacturer comparison if the specs on both uppers, atleast length of barrels etc, aren't the same?

Print and parts would cost under 10 quid. But watch airsoft manufactures will start selling these at 50

Thanks for the amazing video!!! It was a lot of help! Btw a cut up golf tee works great as well for holding the trigger spring in place. In case you don’t bow hunt.

They sent me the site

Dude, thanks! Searched everywhere for a diagram and couldn’t find one, took a buddy’s apart. I did use a bolt for the trigger pin and it pushed out just fine. You’re a lifesaver, thanks again!

Great video man helped a lot

I always said I truthfully dont believe that Aero Precision is a higher quality rifle over a PSA. Ppl will swear that PSA is junk and Aero Precision is 1000 times better than PSA but, I dont believe that to be true. I think PSA gives you great bang for your buck and Aero Precision is actually overcharging for what you get from them. Just my opinion.

THANK YOU SO MUCH WHAT A PAIN!!!! You truly helped me out Big Time And I Appreciate it!!!! I used a Allen key for my makeshift pin. I got it going and wanted to say thanks.

I like psa rifles more bang for your buck 💰

Really informative and well put together. Your content is criminally underrated.

The video is much appreciated. I was one of those who took it apart without researching first. I’m working on a CVA hunter 7mm 08 for a friend. It’s exact trigger assembly to the model you were working on. Thanks again.

I'm assuming it would work but I have a few electric m4 drum mags and I like to run them on my 249 but they tend to be in the way and don't load well being at almost sideways. Would you think this would be strong enough to support a drum that holds 2000 rounds? My drums have a printed top to them as is so you can take the mag well part out and change it to a different platform, how hard would it be to print a curved extension that could be attached to the body of the drum.....think a m4 mag that makes a 90° curve.

More reliable than the Buck Mark? That's a bold statement!

You should see some of the guns they put out in the 80’s. Very poor quality

PSA has crap for QC

Great info, I got a lemon. Just wanted to share an issue I had with a new S&W compact 22. Purchased new on 4/5/2022. Back to store for warranty repair 4/6/2022. Two issues, 1. pull trigger, pistol does not fire, hammer does not drop. Pull again does not fire, pull again and fires. Very intermittent. Removed slide and it looks like the trigger bar is glancing off of the sear, touches it but does not move it. 2. Second issue, much worse, sometimes when you pull the trigger the trigger bar moves the sear off of the hammer engagement slightly. Hammer does not drop, Pistol does not fire, but a light touch the trigger again and pistol fires. Appears to move the sear the rest of the way and drops the hammer firing the pistol. Very dangerous. Not sure what S&W will do, but we will see. If you buy one check it before you leave the store.

Know exactly what you're talking about, when you get the rear sight adjusted and set there's only about one full turn of the screw left before it falls out. That adjustment screw just needs to be longer, meanwhile I'll use some loctite and keep an eye on it.