Відео

I got mine for $97 on sale. Baby blue. It has a bad buzz due to a Grounding issue somewhere but after shielding the pickup cavities, running grounding wires and shielding the control cavity, now it is dead silent. I also re soldered my Jack just to be safe. The setup was great and fret ends felt nice and the fretboard was rounded. 🤷‍♂️ my fretboard was a nice dark Purple Heart. Seems like yours is laurel or pao ferro?

Could you do a more in depth explanation of how you replaced the jack? I have the same bass but in grey and I have to replace the jack but don’t know how to do it

Can you get me one of these?????

How do you call grote???

Where you buy???? I want natural with trapeze tailpiece.

Beautiful playing!

I picked one up at guitar center and I found it be fine

Thanks for all the help! Great video.

Killer guitar. Seriously. I had the shell pink. So you installed hipshot lockers? Why wrap the strings around the tuners? 🤔

Thanks, are the pickups microphonic?

I have to try this. I have a beauiful Classic Vibe 60s Custom Telecaster that has upgraded hardware, including bridge, electronics, switch and pickups. It plays and sound great... but it is noisy. I have have been told by two luthiers that the noise is normal for single coils, but I have quite a few other single coil guitars, including an American Standard Telecaster and they're not noisy. I really love this guitar but the electrical noise really ruins the experience for me. If I touchthe bridge plate the sound stops. Touching the strings help but there is still a bit of noise. But otherwise there is that constunt hum or however you describe it.

Nice

great job !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

i would get a little file and groove that dude deeper in the saddle

It sucks because they look so cool

Looks like QC issue, will definitely evaluate if I decide to get one, thanks for the heads up!

WauwWauhWahuWauWAuuWauhWauu

YES! I’ve replaced these input jacks soooo many times only to have them fail again in a year. Just tried this on a Frontman 25R, and it works like a charm. You rock!

That’s awesome we had a 1/4 eclipse in Orlando ☀️

Un solo muy epico! 💥🤘

First like 🥳

What type of wire did you use? I'm having trouble finding wiring to connect the input to the circuit board.

great work dude! I need to get this donde to mine.

Great video. Out of interest why didn't you copper tape the cavity while you had it open? I see another of people doing this.

What did it sound like or what was it doing before you fixed it ? I wished you'd filmed it as a reference for the noobs like me 😂

Why my cv when i turn up volume or i lower my volume my guitar get noisy sound

For me; 125.00 from GC, one slightly high fret (13) to level and sharp fret edges to polish up (no fret sprout) . Raised the pickups. The neck was spot on, I found no ground issues and the pickups sound great to me. I have an advantage over other beginners in that I can do the setup myself. Overall I really like this guitar. A setup would have run 100.00 if I had taken it to a good shop, so at 225.00 in my opinion it is still a good deal.

Get an ultrasonic bath, cleans up hardware and strings easy, couple of vids on my channel

Got this guitar delivered today. Pretty well set up right out of the box. Plays well and all it really needs is a little fret polishing and light sanding on the ends and it's ready to go. I'm just wondering how you get the screw driver in to adjust the bridge for the middle strings if I need to fix the intonation. Seems like you did the low E and that was pretty easy to reach. Ideas?

I have one of those new relic'd FFST's and it's phenomenal for the money! It actually has one of the best playing necks I've ever played. It did have a couple flaws such as the output jack had to be screwed in further and the tuners were the worst I've seen in a while but I can't believe how level all the frets are! I pay to get my guitars plek'd and it's just as good as those as far as having low action with no problems!

Their customer service never responds if you have a problem. Buy at your own risk.

Intonation, set the neck straght, polish the frets, put Ernie Ball 010's , and it rocks!

how are the stock pickups compared to the EMGs?

I don’t know if you’ll see this comment but I have the same guitar shown in the video and I can’t stop it from buzzing, I already tried adjusting the trust rod.

thank you was very help full...short video staright to the point cheers ..have one question please.... when u check string height at 12 fret do you still have the capo on the first fret or there is no capo ....much appreciated

Prob cut the neck pocket too deep - shim the neck. Guitars 101.

irritating!

Dean basses are perfect for a few metal and punk sub genres: Crust, Ska-core, D Beat, Street Punk, Djent, Meatalcore, Black Metal and Deathcore

Did you need to do any fret ends?

Nice job, and great looking guitar, especilly for the very low price.

Just picked one up on clearance at my Local GC for $350 out the door and the action is as low as my sadowsky and Lakland basses.

They did use different pickups I have one with 3 adjustable screws on the pickups

Thanks great video. I put 9-42's strings.

Can grab one of these for $350 in pretty good shape. Curious what you paid for this one and if you think that's a good deal. Seems like it to me. Great video, thanks!

If I just got mine today how long should I wait to make adjustments to the truss rod?

Can you run this through the spark 40?

Dang it, I was only tuning the bottom part and the Allen wrench doesn’t work on it anymore because I burned it out 😢so now it’s like an inch off the board

I bought a used 5 string model. I was surprised because there wasn't a scratch on it anywhere. It still had the plastic on the pickguard. Took it home and did a setup only to find the same issue with the G String. The D string was able to be adjusted, but the saddle was nearly on the deck to get it close enough. I contacted Fender and was assured that they had not had issues with the bridges on these guitars. Turned out it has enough neck twist to cause the problem. It went back to the store. I found another used one at a different store. It set up perfectly and is a real joy to play.

It's an easy fix if you can identify where the hot and ground are on the board. I have the same crap input jack (Fender Frontman 15G) to replace, how to figure out the ground and hot spots on the board? This jack have no marking of any kind

If it was that big of a piece of c***, why don't you just send it back?