Відео

Upgrade from a 5 gal. bucket to a 30-32" trash can with either 2.5" or 4" cyclone ports to your shop vac.

You’re not the only person that’s having problems with luxury vinyl flooring or laminated flooring. I hope somebody files a major lawsuit against these companies.

I know you said you been in construction for years, but that siding you are puling off has been around for years, it is t111 plywood and not the smart siding. Also, I would have just put new siding over what is there, one important thing you forgot, anytime you put siding on walls especially t11 it is a must to use house wrap. It needs to breath and have some kind of barrier for moist and weather exposure. Other than that good video and at least you are getting it done.

Yeah I made that mistake on pouring mine right now and it came out blotchy and clumpy 😢 and now I just have to wait for it to Dry inside my house😅 I wish I had seen this video before I did this 😫😵‍💫

Thank you, your video has given me the courage to try to replace some baseboard trim.🙂

This is the best video iv seen on making these

Thanks for sharing this information, super helpful!

Removed from my recommended list.

Excellent video. God bless you and yours. Praying for you.

How do you do your vibrating? Thanks mate 😊👍

That t111 is not cheap anymore.

Under what circumstances would one use an LVL (laminated veneer lumber) over PSL (parallel stand lumber) and vice versa?

A lot of beginners don’t own a miter protractors

Great advice here

Lifesaver! At about 5:40 plus you gave me the best method yet to simply and quickly note differing levels. I’ve got to sort out and level a new floor on sagging uneven joists and this is the best way to get my measurements that I’ve found. ❤

Jim thanks for video setting up dado blades I just got set for Father’s Day and you’re video was the best explanation how to set dado blades.Thanks also watched video to make zero clearance throat plate for dados.I just subscribed thanks again hope you put out more videos have a great weekend.You explain very well in you’re video great teacher.

Great idea with that jig. I suppose you could add one more piece to the bottom of the jig that sticks out in the back so the work piece would sit on that rather than the table top. Then you don't need a super flat bench.

Those yellow plastic miter boxes are so dangerous. I accidentally cut off my left leg, mid thigh, with that exact unit.

Does it require a smoother concrete surface or can be applied on rough concrete surface?

im using it as a router fence.

It turned out really nice. Thanks for the great video.

This video made a day a lot easier! Thank you, sir!

If you need the complimentary angle mark the bench with the bevel, put framing square on the mark, mark the other leg of the square, and set your bevel to the new mark

Thought I was listening to Donald Sutherland for a minute there...

Is there a way to safely fuel a tiny generator without shutting it down? To connect an external tank?

What is the advantage of using LVL instead of a steel beam? In my opinion, the small difference in cost, when labor cost is factored in, is really a non issue. So why use LVL instead of steel?

You wouldn't need the gym lugging that fecking monster all day LOL

I like sazsaws but I can do more with an angle grinder I can make an angle grinder more tools than that one

One of the things I see in may of these first time trial reviews is a slight misunderstanding of how the rubber fingers work in Bow's feather boards. When you try to test the holding power by pulling your work-piece back against the feather board, you will notice that the piece can move backward a few millimeters with minimal friction. That is because the laser-cut shape of the fingers allows some movement in both directions at first, but in the reverse direction the fingers lock one against each other, and AFTER they lock, the piece becomes VERY hard to move backward any further. That few millimeters of movement should not put anybody in danger.

What is the purpose of that flashing

I need to do this for my house and wished that you could do it for me.

Great job 👍.

I have water heater like yours but it has water pan underneath it how do i clean out my water filter?

Going to try this method for cast in place. Does misting the top still apply?

Would have been helpful if I could have actually been able to see what you were doing at the most important parts of the video but you blocked my view.

Could I use an 24' LVL over a 22' garage roof? I want to use it as a ridge beam. I will be putting a sheet metal roof on the garage. The LVL in question is a 1 3/4 x 9 1/2 1.9E. Thank you.

How did you find the highest spot?

I want a generator that I can use for welding and grinding, what size do I need?

Thank you for sharing your knowledge.

I just bought a reciprocating saw and I was looking for more usages than just wood and metal cutting, those spider blades you showed are amazing. Thank you for your informative video.

Hi, it's 2024 my first time watching your channel. I'm planning on updating my interior doors and need a saw. I was planning on buying a saw and after watching your video I won't have to, because I do have a reciprocating saw. So, thank you for your channel, I will be watching more.

Great video. I've just discovered a whole lot of rotten joist and subfloor from a leaking hot water heater. Water was going under a linoleum flooring and not apparent until the floor started to sag. I'm going to have to do this same thing to an end wall in the kitchen. I knew how to sister the 2x4 studs in but the 2x8 cross brace was what I was wondering. Wasn't sure how to support the whole wall while pulling out the sill/rim joist. This helps SO MUCH.

He's a corporate shill for Home Depot!!!

I applied using a squeegee, brush, and roller. The squeegee worked well. I would pour product and spread with squeegee, then go over with roller. Seemed to make the product go further.

Great video thanks

Thanks I never knew of all the new attachments available 😊

No "slaking" time?

One of the least used tools I've owned. It's not good for accuracy, speed or cutting tree limbs. Cordless chainsaw way way faster. For tight spaces, oscillating saw is better.

Excellent review. Thank you!

Will it run an AC unit?