Відео

In my experience I cracked my front frame horn. I'm sure pretty uncommon but that was the culprit. Welded up and ready to go again

Lower control arm bushings

100 ch ?

four stroke ?

Hello sir may i ask , what is the pitch of your prop and do you have a special nosecone on the engine, i self have a hpdi 200 and want to make it faster, and what about a jackplate , regards dirk

Mine was doing the same thing, it turned out to be the alignment bolts on the control arm and the bolts that hold the rack and pinion, I’ve tightened them and the popping noise it’s gone for good 😀

tengo ese problema en mi 2008 tacomo lift 3in

Is that normal

I have the same problem on my 2015 Toyota Tacoma a popping noise not sure if it’s the control arms

I have the same problem. Do you find solution

Have any issues with motor? Like power head , Trim, ect?

Don’t put junk on nice vehicles

No on in this comment section knows wtf their talking about. There is no torsion bar on these trucks and on this truck the sway bar has been removed. Check the cv axle where it goes into the differential housing. There's an issue with the needle bearing inside the diff. Ecgs has a remedy.

It's the control arm bolt it shifts back and forward I got under the truck and my friend was turning the wheel and saw it

I have the same issue I've replaced everything control arm bushings ball joints tie rod ends removed my sway bar new bearings new cv axles and no change seems to be during steering and going into reverse on mine. But yours seems to do it more often is the uca contacting your spring possibly

What was the problem?, ever figured it out?

On my Taco, problem was that the sway bar was rubbing slightly on the shock coils, bought the sway bar relocation kit for $40.00 and that solved my problem. With this video it appears from the viewer angle that the uniball cup on the upper control arm is rubbing with the coil although I could be wrong. It looks like you removed the sway bar so that can't be the problem.

Did you source the problem yet? If not does the popping occur when you step on the brake pedal?

Axle

Put sway bar relocate on problem should solve lol, I just did my and it gone.

sinking?

Sounds like a bad CV.

What was the issue ?

Any damage?

Pretty smokey, but I don't care. I'm one of those unique types that enjoys the shit out of scrubbing down my firearms!

do you find those 29s rub anywhere during the suspension flex or full lock turning?

what were you using for bait?

*check sway bar links is what i meant

Your uca isn't hitting your spring. That white bit that looks like a chip is the sticker pealed off (I have the same OME on my truck) check control arms. Your truck doesn't have torsion bars. Torsion bars were replaced as soon as the tacoma came out. Toyota pickups had torsion bars.

its sold

still have it

Instead of beads why not use 50/50 antifreeze and water?

Look at your coil over! There is clearly wear / rubbing mark on it where the paint is chipped off near the top, considereing the spring looks pretty damn clean and the fact your a arm is super close i would suggest that they are rubbing together. The spring def rotated to allowing us too see the rubbing mark. Change out your a arm or get a narrower spring.

tighten sway bar bolts they are loose

Nashville TN. Ready to wheel when you are. We are all within 5 hours

how far from Columbus are you guys. I would like to wheel. FJ40 linked on won tons.

Video credits.

Pitbull Rockers sound good trying to find traction 😃

Punching the trigger

Punching the trigger

Nice Trails, I'm going have to go up to TN. some day, Nice Vid!!!

Well I replaced everything just about trying to get rid of the noise. Coilovers along with new upper and lower control arms.

I have this exact noise and have been trying for 3 months to figure it out!! What's the answer? We don't have torsion bars (2011 Tacoma), and I haven't seen any of my own videos where the uca hits the coil. Have you found the source of this noise???

salfidel is right its ur control arms hitting the coil spring.

Any update on the noise? I have a similar sound on my 09.

That's an awesome looking 80! Needs a front locker though.

No. I have 10oz in each 35. Some speeds are fine. Some shake like hell

Do they work all the time? I'm running 8oz in my 35s and they still shake.

My 06 does this after installing biltstine 5100s but only over bumps

hey man great vid.... Subscribe and check out some of my vids !