- 74
- 194 186
MattyTsGarage
United States
Приєднався 9 лип 2020
I am starting this channel because I believe it will be the best way to get advice on how to get my grandmothers truck back in running condition.
Start and Drive S197 Mustang (5th Gen)
Starting and going for a little drive in my 2006 mustang gt manual. A little review on how the car has been in my couple years of ownership.
Переглядів: 18
Відео
Putting Down the Soft Top S197 Mustang
Переглядів 14Місяць тому
Very quick display on how to put down the soft top on a s197 mustang convertible!
Canister Purge Valve Replacement Chevy Traverse 2018-2023
Переглядів 703Місяць тому
Canister purge valve replacement on a 2018-2023 traverse! Step by step on how to replace this part.
Changing Foot Controls on Yamaha Roadstar Warrior
Переглядів 817 місяців тому
Changing motorcycle foot controls on a Yamaha Roadstar Warrior! Got the parts off another Roadstar, didn’t line up perfectly so needed some drilling. This bike has a rod setup for the clutch.
Yamaha Roadstar Warrior Walk Around and Start!
Переглядів 1338 місяців тому
Walking around and starting this 2006 Yamaha Warrior. Going through the specs and all the quirks of this bike. If you are thinking about buying this bike or want to see what it looks like this is the video for you!
Junkyard Run! Parts, Carnage, and Fun.
Переглядів 1878 місяців тому
Junkyard Run! Parts, Carnage, and Fun.
2010-2017 Chevy Traverse Coolant Temperature Sensor Change
Переглядів 9 тис.9 місяців тому
2010-2017 Chevy Traverse Coolant Temperature Sensor Change
Changing Low Beam Headlight 2009-2017 Chevy Traverse
Переглядів 2,2 тис.9 місяців тому
Changing Low Beam Headlight 2009-2017 Chevy Traverse
Taking out DENTS on rear truck panels!! Failed panel welding
Переглядів 2853 роки тому
Taking out DENTS on rear truck panels!! Failed panel welding
Trying to straighten out a BENT TAILGATE. Grandmas 1952 Chevy
Переглядів 1,2 тис.3 роки тому
Trying to straighten out a BENT TAILGATE. Grandmas 1952 Chevy
Pulling panels off 1952 Chevy truck! Dealing with clutch head bolts!
Переглядів 6183 роки тому
Pulling panels off 1952 Chevy truck! Dealing with clutch head bolts!
Finally got some of GRANDMAS TRUCK home! 1952 Chevy Truck
Переглядів 2,3 тис.3 роки тому
Finally got some of GRANDMAS TRUCK home! 1952 Chevy Truck
How I got my DREAM CAR for CHEAP! The junkcharger story.
Переглядів 2663 роки тому
How I got my DREAM CAR for CHEAP! The junkcharger story.
Junkyard hunt for SMALL BLOCK Chevy 350!!!
Переглядів 12 тис.4 роки тому
Junkyard hunt for SMALL BLOCK Chevy 350!!!
1952 Chevy Sat for 40 YEARS!! Will it turn over? Will it Start?? Grandma truck restoration part 2
Переглядів 8 тис.4 роки тому
1952 Chevy Sat for 40 YEARS!! Will it turn over? Will it Start?? Grandma truck restoration part 2
Finding parts for my grandmas 1952 Chevy truck! Junkyard hunt!
Переглядів 3,9 тис.4 роки тому
Finding parts for my grandmas 1952 Chevy truck! Junkyard hunt!
Restoring my Grandmas Truck Episode 1!! 1952 Chevy Truck Restoration
Переглядів 17 тис.4 роки тому
Restoring my Grandmas Truck Episode 1!! 1952 Chevy Truck Restoration
Strap??? F'ing genius!!!
Worked pretty slick
This worked perfectly on my Chevy Traverse 2019 Premier. Thank you for the details and demonstration!
Did your engine light went off right away after replace the valve ? Mines still on 😢
@@erickventura2452 It is a latched signal. You need an OBD device to reset it. Or you could take it to a repair shop and have them reset it. I use the ELM 327 WiFi wireless device.
Mine failed after a year . Off to buy another one . Luckily it’s only $40.
I think mine just failed today after 11 months
Can you do a oil catch can installation on this 2018 Traverse, please? And have you check your intake valve for carbon build up? Mine has a lot of carbon build-up on the intake valve which is the reason why I want to put in a oil catch can once I do a complete carbon build up cleaning on the back of the intake valve.
Thanks for the help! A few comments. 1) Removing the 10mm mounting bolt about 2" below top of oil dip stick tube allows you to flex the tube a bit. 2) The release tab on the sensor wiring harness is impossible. Just go ahead a break and remove the brown plastic part, then it comes off. Still snaps onto the new one. 3) Old sensor took a 20mm, new sensor took a 21mm.
My plenum is held on by my oil cap - which I hate... but not as much as I would hate having to get a 10m and plugs like this. Ew.
Those are c10’s
I just wanna say thank you so much for sharing this video. You helped me out in a big way I followed your steps and I fixed my Chevy traverse 2017 thanks again bro💪🏾💪🏾💪🏾💪🏾
1952 was a great truck , the push button door handles were a big improvement .
Good deal.
Not guna lie but this was the worst video ive seen in a while 😂 calling c10 chevys s10 lmfao 😂 s10 is a 1/4 ton c10 is 1/2 ton c20 is 3/4 ton c30 is 1 ton 😂 calling 4.3l v8s lol when they are v6😅 calling tbi 2 barrel carbs lol like if you like this stuff for a hobby do some research before making a vid so u dont look like a complete dumbass😂 atleast i had some good laughs 😮😂
Nice G
And thats where they belong!
It’s the shit quality from dodge.
Omg it is sad to see those once loved beauties rust away.
Totally agree
Where is this?
It's pronounced faguar
if you see any early 90's XJ6's lemme know, i need parts 😂
jag-u-lar
That's extra! 😂
wagons are ugly imo imho
I like them. not sure what problems they have
Mark 10, 420G
Jaguar Mark X. After 1966 named Jaguar 420 G
Rx7
You got it!
Lemme guess? From Detroit...🤔🫣😉
Old rx-7!
Nice i was gonna say Datsun
It's a red car😂
First glance i knew what it was 😂
every build starts with a shell
That’s a FB3S/SA22C chassis Mazda RX-7.. the reason it’s still there is because the shell is still incredibly valuable
Chrysler imperial
Looks like a solid one. Lots of them are rusty
Bummer to see it picked clean
1st Gen RX-7??
You got it! Hard to tell with all the parts stripped
Jaguar mark X
Know around the year?
@MattyTsGarage its probably a 1963 or 1964
Jaguar
I know the name of that car rust bucket
Front end definitely looks like a jag
That’s what I figured!
Jaguar
Kinda looked like that to me
Good, I have one that’s tuned with bolt on’s.
Looks like a fun car!
Honestly black guys have the worst taste in cars. Especially the “modifications” if you want to call them that. Their shitty taste rivals 70+ year old men that chrome out everything.
Is that image of a dude getting pissed on with shit in his mouth?
I mean they are a bitch to get in and out of, built by DaimlerChrysler so it’s 90% Mercedes SLK320 so they aren’t very reliable but they are decent performance wise
They’re very reliable drivetrain wise. Electrical wise they have issues which can be fixed easily if you know what you’re doing or have a good shop to take it to if not then you’re screwed.
I drove one for a little while it wasn't too bad it was super fun to drive tho
Has a 6 cylinder right? I’d imagine it would be speedy
@@MattyTsGarage Yeah I had the supercharged version, and because it was kinda small it was zippy around corners and stuff.
Never seen one.
Neat looking cars
It's actually a Mercedes with Chrysler badges and body panels
Would never have thought!
@@MattyTsGarage it's the only car they ever did together I believe. It was a huge failure but a nice concept
That be a rust bucket.
No saving that one
NO
Bro if those things are rare then SC has them all😂 they are everywhere here
Rarely see them up north. Road salt is a killer.
Must be! I never see them here
Fierro’s are rare but they are compleat shite
Ya that 163 huge whp 😂