Dan's Auto Diagnostics And Repair
Dan's Auto Diagnostics And Repair
  • 24
  • 21 782
2015 Chevy Cruze Brake Pads and Rotors
2015 Cevy Brake pads and rotors replacement. Someone tried to replace the pads on this vehicle and did not use the proper tools. Now the brakes are grinding. In this video I show you how to do the brakes properly. I try to be as detailed as possible so everyone can do their brakes at home. The Disk brake tool kit is not expensive. The video is a little long but I wanted to cover everything. Enjoy.
Переглядів: 99

Відео

2019 GMC Terrain Fuel Tank Replacement
Переглядів 52День тому
2019 GMC Terrain Fuel tank replacement. Unfortunately, I don't have my camera equipment with available so I'm doing this one with one hand. More and better videos to come.
2007 Chevy Express 2500 - Dome light blinks with blinker and oil pressure gauge is maxed out.
Переглядів 803 місяці тому
My 2007 Chevy Express 2500 Had a dome light that operates correctly until I turn on the left blinker or the hazard lights. When I turn on the left blinker, the dome light blinks with it. My oil pressure gauge is also a problem. It always reads 80 PSI. I have a B2615 Passenger Compartment Dimming 2 Circuit, and a P0522 Engine Oil Pressure Circuit Low.
Toro Dingo Hydraulic Ram Seal Replacement
Переглядів 2944 місяці тому
In this one I replace the seals for the Hydraulic ram.
Husqvarna YTH21K46 will not move forward or backward.
Переглядів 3,2 тис.4 місяці тому
In this one, I replace a couple drive belt pulleys, a drive belt, fuel filter, spark plug, oil, oil filter, air filter, and breather filter.
2000 Chrysler Sebring Fuel pump replacement.
Переглядів 3924 місяці тому
2000 Chrysler Sebring Fuel pump replacement. Tools used: Launch X-431 PRO, and test leads with accessories.
2014 Nissan Rogue check engine light and weak A/C (Part 2)
Переглядів 395 місяців тому
In this video, I get the car back with the TPMS light on. Tools used: Autel MaxiTPMS TS508WF, and Launch X-431 PRO3S
2001 Ford F 250 Super Duty
Переглядів 555 місяців тому
Customer complaint: It leaks oil so bad it leave a trail down the street. He thought it was the oil lines, so he bought new oil lines for me to install.
2014 Nissan Rogue Check engine light and week A/C (Part 1)
Переглядів 875 місяців тому
In this one I investigate a short to ground code that sends me on a wild goose chase. Alldata wasn't very clear as in a photo as to where the sensor was located and contradicted the wiring diagram. A/C wasn't efficient enough for the customer, so I looked into that. I use the Launch X431 Scan Tool and some Testo tools to troubleshoot.
2013 Smart Car, won't move in any gear.
Переглядів 2,8 тис.5 місяців тому
Customer complaint: No crank no start, and won't move in any gear when it does fire up.
1993 Yamaha Virago 535 Tire Change and Balance
Переглядів 3225 місяців тому
1993 Yamaha Virago 535 Tire change using the Harbor Freight Tire Stand and Bead Breaker.
2002 GMC Savana Brake Line Replacement
Переглядів 1385 місяців тому
2002 GMC Savana 2500 Brake Line Replacement.
2008 Nissan Versa: CV Axle, Control Arm, and Lower Ball Joint Replacement
Переглядів 3445 місяців тому
CV Axle, Lower Control Arm, and Lower Ball Joint Replacement.
2010 Husqvarna Riding Lawn Mower YTH21K46 Crank No Start
Переглядів 8 тис.6 місяців тому
2010 Husqvarna Riding Lawn Mower Crank No Start.
Pittsburgh Motorcycle Tire Change Stand With Bead Breaker
Переглядів 3166 місяців тому
Pittsburgh Motorcycle Tire Change Stand With Bead Breaker
2002 Dodge Grand Caravan. Cluster, and blinkers not working.
Переглядів 1226 місяців тому
2002 Dodge Grand Caravan. Cluster, and blinkers not working.
1996 Honda Magna 750 Rear Tire Change
Переглядів 4936 місяців тому
1996 Honda Magna 750 Rear Tire Change
2017 Ford F 250 Super Duty Diesel Fuel System Flush
Переглядів 526 місяців тому
2017 Ford F 250 Super Duty Diesel Fuel System Flush
2015 Chevy Sonic AC not blowing cold
Переглядів 4,4 тис.6 місяців тому
2015 Chevy Sonic AC not blowing cold
Trailer Lights installed on a boat trailer
Переглядів 186 місяців тому
Trailer Lights installed on a boat trailer
2010 Nissan Xterra Clutch Replacement
Переглядів 1796 місяців тому
2010 Nissan Xterra Clutch Replacement
2003 Harley Davidson Buell Ignition fuse blowing
Переглядів 1806 місяців тому
2003 Harley Davidson Buell Ignition fuse blowing
1981 Yamaha 650 Not charging
Переглядів 916 місяців тому
1981 Yamaha 650 Not charging

КОМЕНТАРІ

  • @titanicsauce2152
    @titanicsauce2152 7 днів тому

    Excellent instructional video for diy.

  • @Sans_________152
    @Sans_________152 9 днів тому

    All rusty not good

  • @dancassidy7471
    @dancassidy7471 Місяць тому

    aha moment thanks I need a new tire dor my 94 magna not sure the size...it is a Dunlap

    • @DansAutoDiagnosticsAndRepair
      @DansAutoDiagnosticsAndRepair Місяць тому

      Sorry this reply is so late but I'm in the middle of moving from Florida to Michigan. It's been crazy for me lately. I can't remember the tire size on the Magna. I'd have to go through the video again and see if I can see it on there. I'll be making more videos soon. Right now I have to get the shop together. Thanks for watching my friend.

  • @Gonxp12
    @Gonxp12 Місяць тому

    My smart sometimes wont go on reverse especially on hills, but drive and neutral works fine, what could it be?

    • @DansAutoDiagnosticsAndRepair
      @DansAutoDiagnosticsAndRepair Місяць тому

      I could be lots of things. Mechanical, or electrical. You just never know with those cars. If you can pull a code from it, I can point you in a direction, but without being there it's kind of hard to say. Text me back if you can pull a code and I'll look it up. Thanks for watching.

  • @stellamatutina3573
    @stellamatutina3573 2 місяці тому

    I have Husqvarna ST 138 2015 model. when I push the forward pedal, the mower moves in reverse, the reverse when I push down is okay, but the forward goes in reverse too..? It has me beat what the problem is

    • @DansAutoDiagnosticsAndRepair
      @DansAutoDiagnosticsAndRepair Місяць тому

      I haven't seen that one yet. Have you checked the linkage to see if it's connected properly? Sorry about the late response. I've been moving from Florida to Michigan so I've been busy. I'll be putting out more videos soon. Thanks for watching and I'll see ya on the next one.

  • @yertelt5570
    @yertelt5570 3 місяці тому

    Nice video, just a heads up, the number in parenthesis by the fasteners refer to their parts list number, not quantity. It confused me at first too. Also, the sliding pin can be used as a fulcrum to push against with a tire iron or spoon to pop the tire off the rim. Your tip to use it to hold a spoon in place was money! Anyways, thanks for the video.

  • @galloway74
    @galloway74 3 місяці тому

    Awesome 👍

  • @goldwingconepatterns2565
    @goldwingconepatterns2565 4 місяці тому

    The Canadian version sold by Princess Auto in Ontario has the flat plates connecting the two rings to each other in 4 places. There are a few versions of the tool. Your video showed the reason for the cotter pinned large pin which I didn't have on my instructions. Ours is blue instead of black. Thanks. Good instructional video.

  • @jadney
    @jadney 4 місяці тому

    Perhaps you fixed it off camera, but you left the drive belt outside the 2 J-hooks and on the wrong side of one of the pulleys (leaving it rubbing on one of the guides.)

    • @DansAutoDiagnosticsAndRepair
      @DansAutoDiagnosticsAndRepair 4 місяці тому

      The J-hooks are for the deck belt, not the drive belt. The drive belt goes on the upper pulley. I didn't film the installation of the deck. Thanks for watching, I hope I'll keep you interested. I'll see ya on the next one.

  • @06021988jolanda
    @06021988jolanda 4 місяці тому

    Your awesome I have a smart car myself but your awesome for even figuring that out

    • @DansAutoDiagnosticsAndRepair
      @DansAutoDiagnosticsAndRepair 4 місяці тому

      Thank you very much. It helps to have ALLDATA. Without that, I couldn't look up schematic diagrams and fix cars efficiently. It's $200 a month for a full subscription but there's also a DIY subscription for a lost less. You can pay for specific cars for much less. Thanks for the compliment. I appreciate you watching. Hopefully you'll be watching the next one. I'll see ya then. Thanks for watching. You're helping the channel. I have 55 subscribers as of this reply. Hopefully I'll have many more.

    • @KT-TV
      @KT-TV 4 місяці тому

      Smart ForTwo 451 superb definitely not a "little electric car". Most Europeans up to about 6ft 6" can fit comfortably fit with no issue. Once you adjusted the seat you seemed to fit ok. Outside the USA we try not to destroy the planet by using huge gas guzzling cars as we prefer economical cars. These computerised actuated manual gearboxes are a bit finicky but this is a common fault on this car. Good logical fix from a position of inexperience shows your mechanical fault finding skills. Well done! ❤

  • @ourv9603
    @ourv9603 4 місяці тому

    That mower has a 46" deck? Ive never heard of a 46. All other makers offer a 42 then a 54. !

    • @DansAutoDiagnosticsAndRepair
      @DansAutoDiagnosticsAndRepair 4 місяці тому

      Yes, this one is a 46" deck.

    • @jimsvo4486
      @jimsvo4486 4 місяці тому

      I just got my neighbor's (sitting for 5 years) 1998 Murray with the 18.5HP Briggs opposed twin flat head. It has a 46" 3 blade deck that needs two belts.

  • @danmiron3210
    @danmiron3210 4 місяці тому

    surprized you didn't sharpen the blades while you had the deck off brother.keep it up

    • @DansAutoDiagnosticsAndRepair
      @DansAutoDiagnosticsAndRepair 4 місяці тому

      I only do what they pay me to do. I'd rather replace them. That's business. You know how it is. I can only suggest, it's up to the customer rather or not they want to pay for it. You'd be surprised how many don't go with my suggestions and it ends up costing them more money. It is what it is.

  • @danfrench5221
    @danfrench5221 4 місяці тому

    did you not see the top of the crank where the flywheel is moving back and forth I'm thinking it's got a bearing bad in it on the crank I think you got problems inside that motor I'm just saying

    • @DansAutoDiagnosticsAndRepair
      @DansAutoDiagnosticsAndRepair 4 місяці тому

      I'm going to check that and see if it's a problem. I'll get back to you on that one. Thanks for looking out, and thanks for watching.

  • @zackthomas1944
    @zackthomas1944 5 місяців тому

    Nice👍🏽

    • @DansAutoDiagnosticsAndRepair
      @DansAutoDiagnosticsAndRepair 5 місяців тому

      Thanks for watching. Ring the bell for more content and leave me more comments. I'm new on UA-cam, so it'll help if you have any suggestions, or something you'd like to see. Thanks for the thumbs up, I appreciate it.

  • @Dawn-je6ek
    @Dawn-je6ek 5 місяців тому

    I can't believe this guy posted his own stupidity and calls himself mechanic when he can't even maintain his own vehicle ..

  • @philliphall5198
    @philliphall5198 5 місяців тому

    Sounds like no compression, turning really fast

    • @DansAutoDiagnosticsAndRepair
      @DansAutoDiagnosticsAndRepair 5 місяців тому

      That's what I was thinking when I first heard it. It's still running great today. I'm glad it wasn't that. I'm new at this UA-cam stuff, so I appreciate the support. Thanks for watching.

  • @Terry-i4c
    @Terry-i4c 5 місяців тому

    Will this make the cooling fan not work as well

  • @grazz7865
    @grazz7865 5 місяців тому

    The smart car is an AMT transmission (automated manual transmission). If the clutch is worn, it will trip the sensor and you’ll have to change the clutch.

    • @DansAutoDiagnosticsAndRepair
      @DansAutoDiagnosticsAndRepair 5 місяців тому

      In this case, it was just bad connection on the coupler actuator. What I really needed is a jack, so I can get under there and clean it properly and spray it down with Deox-it.

    • @grazz7865
      @grazz7865 5 місяців тому

      @@DansAutoDiagnosticsAndRepair What happens when the clutch wears out? Will you get a check engine light? Or will you just notice horrible shifting? Remember, the smart car is an automated manual transmission

    • @DansAutoDiagnosticsAndRepair
      @DansAutoDiagnosticsAndRepair 5 місяців тому

      I'm not sure if the ECM has the ability to tell if the clutch is worn. I'd imagine you'd just get horrible shifting. I would have to check ALLDATA for theory of operation and available sensors for that. I have not come across that issue. Thanks for watching my friend. Stay tuned for more repair videos.

  • @JMPolteR
    @JMPolteR 5 місяців тому

    I think you should get out from under a rock because as an American you only think that cars have to be BIG and use a lot of gas/diesel, small cars like this are common in Europe as they use little fuel and are ideal for the city, they are Small yes, but that's the idea. You don't need a Chevrolet Silverado to go to work every day and use 5 times more fuel and not find a place to park. You should use your head more and not your stomach.

    • @DansAutoDiagnosticsAndRepair
      @DansAutoDiagnosticsAndRepair 5 місяців тому

      I wasn't saying anything bad about the car. I actually like it. I love how fuel efficient it is. It may not be an ideal car to get into an accident in, but I absolutely love the fuel economy. It brings the travel cost down and the emissions.

    • @06021988jolanda
      @06021988jolanda 4 місяці тому

      @@JMPolteR facts I'm in United States and I got to say I fell in love with the smart for two instantly I wish I lived in United Kingdom I would stay buying the smart for two

  • @dougmacrae9535
    @dougmacrae9535 5 місяців тому

    The fuel filter looks reay bad.

  • @matthewgilmore5307
    @matthewgilmore5307 5 місяців тому

    that would had been a job with out the tire changer !

    • @DansAutoDiagnosticsAndRepair
      @DansAutoDiagnosticsAndRepair 5 місяців тому

      Indeed. I was glad to have it for sure. It'll be a lot better once I mount it on something. I'm in the middle of getting into a big building, so no more working in the dirt. I moved from Bellville Michigan to Vero Beach Florida, and I was working in the dirt there too. It'll be a nice change to have a concrete floor. One day I'll post a video on where I was, and where I'll be. I'm working on it, so keep watching. Let me know if there's anything you'd like to see in the videos. I'm still new at the whole filming thing, and I don't want to be boring, so if you ever have any suggestions for me, go ahead and let me know. I'm open for suggestions. Thanks again for watching and I'll see you on the next one.

  • @DjDaveVoom
    @DjDaveVoom 5 місяців тому

    Gained a Sub Great Work man

    • @DansAutoDiagnosticsAndRepair
      @DansAutoDiagnosticsAndRepair 5 місяців тому

      That's great! I hope you like the content. I'm new to this UA-cam stuff, so I'll do my best to make it interesting. Let me know if there's anything you'd like to see. Thanks for subscribing, I appreciate it.

  • @danmiron3210
    @danmiron3210 5 місяців тому

    you literrally had me crying laughing.Im out here on the curb.I cant even explain.Good job

  • @gloriawilson1533
    @gloriawilson1533 6 місяців тому

    Hi Dan: David Wilson here. Enjoyed your video. Hope the brisket comes out delicious! Getting ready to do similar work on my Escalade. I am enjoying this. Thank you.

    • @DansAutoDiagnosticsAndRepair
      @DansAutoDiagnosticsAndRepair 5 місяців тому

      The brisket was great. I'm glad you like the channel. If there's something you'd like to see me do, drop me a line and I'll see what I can do. Hopefully I can get you out some better content. Thanks for watching, I appreciate it.

  • @MrMont
    @MrMont 6 місяців тому

    That's a lot of work, but, Great Job!