Відео

@@divyanshukumar4470 Thank you 🙏

@SAhellenLily yes...other pole and zero are also there but very far so insignificant!!!

Yes it can be taken as a small signal...I'm slowly increasing its magnitude...so that the current is flowing only one side

okay i will check it once

for the given circuit with Gm cell, capacitive and resistive load, calculate the transfer function and from there find the value of UGB, you can simply see it as a single pole system with one cap and load resistor, so you will have a pole value, find dc gain, then write down the TF, from transfer fxn, find GBW or UGB frequency

Yes, it will be vgs3,4 instead of vth3...missed during writing it

Thank you for figuring out, no one replied to it...so hopefully you are watching very carefully...it's good

@@learningexpress183 Please pin your comment, I just watch and figure out but I wanted to confirm so I looked the comment and confirmed that thing.

@@Himanshutiwari590 or do one thing, find output voltage of first stage in terms of input voltage which is nothing but the gain of first stage and then go for the output shortcircuit current at the output of second stage which is nothing but the gm of second stage hence we will be having relationship between input voltage and output short circuit current

Thank You

Yes, A in the numerator with gm is extra

Thank You Hrishikesh....Such comments motivate me to put my energy in this work

@@hrishikeshsarkar1453 Thank you 🙏❤️

@@soumojitbakshi1635 sure

@@AritraSamanta-r7u great 👍

It's a great feeling once you people like it

Thanks a lot, such appreciations give motivation to work continuously!!!❤

Thank You a lot Aritra...Such comments give energy to work further

@@manishranjan943 no, gate voltage of M3 and M4 is the mismatch modeling between these two transistors only... mismatch between M1 and M2 is modelled separately

@@Sankha-c4n thank you a lot 🙏❤️

@@sohamdas11 Thank you Soham❤️🙏

@@napolean_bonaparte Thank you very much ❤️🎉your words means a lot to me and give motivation to work further 🙏

Thank you so much 🙏, your words mean a lot to me...they give me motivation to work further ❤️🎉

@learningexpress183 carry on bro🥳

@shubhamshahi6280 sure shubam

@@koushiksen9754 project is not that important i hope so...they asked all questions on basics like edc and in some cases analog also but no project related stuff

@learningexpress183 okay

@@infopoint6802 yes it's important

@@infopoint6802 you can't analyse circuits without knowing signals

Semiconductor basics acche se kro, I was selected for this...look at my interview experience in this particular course

I think I have mentioned the questions also

@@dipanjalibiradar you can check the requirements, and also make sure that you are interested in VLSI syllabus...being a CS student, it might be bit hectic to deal with vlsi stuff

@@MithunBarmann yes it will circulate inside the device M3 means it will flow through rds of the device or it can also be considered as drain to source current of M3..at the same time vgs of M3 and M4 are same so this current will be copied and will flow through output short circuit

@@MithunBarmann I think your confusion is that it its circulating in device then why copying? Actually circulating through the device is only responsible for copying, if it will not flow through the device or if it directly goes to supply, it can't copy

@@koushiksen9754 thodi jyada mehanat krni hogi...to cover the VLSI syllabus and its placements preparations...rest koi difference nhi hoga

@@koushiksen9754 for masters if your banch is related to VLSI you will be eligible to sit into VLSI companies

@@learningexpress183 Thanks bhaiya for reply

@@learningexpress183 matlab agar Btech k bad apply karu off campus to Branch k baja se koi dikaat nahi hoga nh?..kiu ki companies mere branch ko mention nahi karte.

@@koushiksen9754 haa yhi problem ho skti hai

@@SATYAPRAKASH-pr4vr okay

@@davidtigga8418 thank you bro

@@YashRPant for the short circuit output noise current Gm is responsible to refer it to input while in case of voltage, gain is responsible where rout is used to refer it to te input, I'm not getting it

​@@learningexpress183 Sry for confusion.. I will go through it once more I was just wondering for which one input referred noise will be less

@@YashRPant okk no problem

as such no playlist is there which tell about better questions but you can follow a particular book...for gate purpose go for sedra smith

@@learningexpress183 ok sir thank you i will look into it

@@AdityaSaimpu look in Allen Holberg

Or switch cap amps in razavi

@@pallavisingh9973 sure...it's my next target..I'm working on it

@@YashRPant yes but while you will do analysis, there is much smaller fluctuations in vx for small signal analysis...so it can be taken as virtual ground

@@YashRPant if not understood yet I'll can take this concept in more detail in some other video

​@@learningexpress183 Okay it would be great.. Thanks!

Thank you! 😃

@@Sachin_Madane sure

Ok bro please Tell me which playlists good and which playlists and videos u reffered