Відео

Looks great!

Thank you ❤

what if any steering mods have u got? looks super stable

Music is so damn annoying makes not wanna watch

how much whp, im looking to boost mine and im trying too compare different whp

Thank you. Best video I've seen so far on this subject. They don't make it easy, do they? But please lose the music.

What’s the exhaust setup? Sounds insane bro

Have a question. Did you have problems with your analog ground? This is straight from Hondata Warning: The ground pins on the analog input connector are connected directly to the ECU ground plane. The KPro and/or ECU will be damaged if power is applied to these pins or a sensor sinks a lot of current to ground through the ground pins. The analog ground should only be connected to sensor grounds that are either dedicated analog grounds or sink very low current (<1mA). Never connect a wideband to the analog ground! The o2 sensor heater will sink far too much current.

Please turn that music off!!

Thank you for sharing. I watched a couple of videos to learn how to do this. I was successful!

Looooool whats up anthony loool

I have the same kit with the same ecu I used to same wired white the red/ brown the solid black and it don't work at all

Thanks for the information, why did you use the 30-300 model? Is that what you recommend or is there another one you recommend?

So you are using the “gauge’s” signal & ground output into k pro and you are NOT running the o2 signal that’s coming straight from the o2 sensor and into kpro is that correct? I just don’t understand why all of the 6 wires coming out of the AEM gauge are all running to the o2 sensor instead of physically having the dedicated signal&ground that are supposed to go into kpro and just have them labeled as output to ecu. My AEM gauge is part# 35-8460 with sensor LSU 4.9 which seams to have 3 wires, but I did not find that part# in AEM’s website parts list for the owners manual.

Uh the music tho

do you still need to ru n the honda o2 sensors?

Hello, so from hondata Analog Input wires what i need.?only the red and black.?And remove Disabling the P1167 (oxygen sensor heater) and P0134 (oxygen sensor response) is can be better for the car.?? Thank you!!!

Nice one bro 👍 💪 🤝 💯

Nice vid, how do you get your pov setup, is it the hat and clip setup?? Or something else

100th sub nice rsx bro

stop talking so i can hear the music jesus

Wish the background music was either lower or not there at all

How did you do this??

If I have a Tune with Kpro would replacing the o2 sensor with this negatively affect it?

What happends to the old wiring thats not connected.doesnt the ecu need this

What gauge wire is recommended

Where did you buy or how did you make the center console magnetic? Extremely clean install!! I had the idea to run magnets on all 4 sides to mount my S6 lite android with a ghost box. But I'm liking your look better.

Bro clean af! Just bought a 2002 Type S. How much did you end up dropping for the turbo setup?

An added tip for anyone doing this. After you remove the staples from the original boot, just pull the boot out. It will be significantly easier to remove the ring off the plastic base. I tried doing your method of removing the ring first and it was a lot harder.

Where’s the gauge pod from ???

Hi mate interested in this setup though I have an ep3. What is the launch port system your using there? could you make a video sharing the details of this setup as I’m very interested in doing the same to mine. If you could show your launchport how you integrates that within the centre console that would be awesome cheers

Is it possible where this can also be the climate control and music din display?

Would love to set this up on mine! How??

Question, what oil line are you using off the sandwich plate to the oil pressure sensor...thank you

Daft question but what's the difference between analog and digital

Good video

Does the black wire have to be grounded to the ecu? Or can I just ground it to where ever in the car and just run the white wire to the analog input ?

Have you tried RealDash? I'm running it. Integra 00 07 k20Z3 swap

Did you have to wire up anything to the hondata like you did o2 sensor?

thanks bro helps alot

You could have run the wires straight back from the connector out the side crack of the ECU with out drilling anything 🤦‍♂️

are you running a secondary and primary o2 aside from the analog wideband?

I literally have a spare tablet I've been waiting for a reason to use

That sounds amazing😍

Thank you for this much needed

so you only used to wires to ecu?

Did u use the solid black or the one with the little white lettering on the Kpro side of the pig tail I recently purchased an AFR gauge for my rsx and was just wondering that question since there is two black wires thank you

im confused because you running a digital gauge right. but selecting anolog in kpro

What exhaust system do you have? This is the best rsx ive ever heard

ƤＲＯ𝓂Ｏ𝕤ᗰ 😒