Відео

No because it's not freezing everywhere. If it was all of the pipes and you closed the faucet then it could explode because the pressure can build up but if you leave a faucet open or if you're only freezing a little section of it then there's no area where water can get trapped. Since the water's pressurized it will just expand back the other way or expand out the faucet that's open. Now if you did this to the entire pipe all the way until the faucet then yeah there'd be nowhere for it to expand

@@pilotavery thanks , I’m going to try it out

Just hire another company. Roto rotter will charge you per minute 😂

Not a DIY channel

Not a DIY channel

Thanks for the comment, your right that’s what the manual says. Small leak like that usually works, but if it something that’s flowing and I want to freeze, I will use a "Quick Sweat" Water Stopper or Jet Swet!

Also if you turn off every other valve you can’t obviously after the main shut off valve it will stop all water flow or at least make any flow down to very low level of water flow.

COLD-SHOT by GENERAL PIPE CLEANERS

We had to reuse the existing meter unions that don’t come in press. Torch is already out to remove the elbows.

@@straightupplumbing 👍

how did the fix go? and where do i shut the water off at?

450

A short answer is. It’s fine. The solenoid is powered by 120 V that when the burner control shut the power down to the pump it immediately shuts fuel off to the gun nozzle, versus having the oil pump slow down with the burner causing unburnt fuel while it shuts off. But you cannot just add a solenoid to a fuel pump, it must be a clean cut pump. Sometimes installers will install what they have on the truck to get you by. But I don’t think it’s anything you should be too concerned about they’ve been running these oil pumps forever.

@@straightupplumbing Thank you sir. I called the repair man and he said he didn't install an A2VA-3006, he installed another non-solenoid pump and just reused the cover, which was my confusion. I was worried not having a solenoid would cause premature wear because my furnace specifically calls for the A2VA-3006 as a repair part. He turned off the solenoid setting on the burner and said everything will be fine. Thank you for answering because it validated what he said so I trust him. It was my first time having service done as I just bought my house. He charged $170 for the fuel pump replacement which I thought was fair.

Thanks Luis! We all love cool tools!!

Not everything is caught on camera, but from 4:11 to 4:20 thats probably when I was fluxing the valve....

Customer works from home and their office is on the other side of the wall... check out our other videos each one has different circumstances, we bring these videos for people to watch and lean something new, but we also respect our customers when we are inside them.

Another excuse

@@straightupplumbing These guys are just haters. Anyone with an idea about life realizes you were being quiet out for respect for the customer. People really act like you owe them something just because they decided to click on your video. Haters gonna hate. Thanks for the video you gave me plenty of info I was looking for and I didn't need sound to get it. Also I totally grasp that there are other videos I can watch and manuals I can read to learn for myself...go figure. Take care and be safe!

That one in the video is a Milwaukee m12

Pipe size and pipe material change the amount of time. For 1” copper it’s about 10 min. Pex, black iron and copper all have different freeze times from 5 min to 20 min. There’s a manual that gives you times for each size and material

After 10 min you can cut it right away, doesn’t need to necessarily “sit”. After 10 min of freeze time for 1” copper you can cut it out right away

@@straightupplumbing cool thanks How about 2” or 3” water lines how long do those have too sit?

What about a lead line??

Because someone asked for it, that’s why! Are you upset? We can’t tell?

Thank you, there are many different terminology’s for a delta R10000 rough in valve, but the reason we chose to title it this way is because of search results. Many people referred to this valve as a diverter valve. www.lowes.com/pd/Delta-5-8-in-ID-PEX-x-5-8-in-OD-PEX-Brass-Diverter-Valve/1000195383?cm_mmc=shp-_-c-_-prd-_-kab-_-google-_-lia-_-225-_-bathfaucets-_-1000195383-_-0&placeholder=null&gclid=EAIaIQobChMIkrDUlbK26wIVAobICh14QAWHEAQYASABEgLiYfD_BwE&gclsrc=aw.ds

Sorry not everything makes it in the videos, issues with videos being to dark, or forgetting to press record :/... but yes when pump replacement we do combustion analysis with smoke test.....

@@gattusoplumbing7639 didn't see the smoke tester or combustion analyzer.

haha, hope they are labeled, not like these!!

oh yeah, definitely a cool tool!

lol... PLUMBERS STICKER WARS!! Thanks for the comment!