Відео

Title:diy how to make a bom from you bulb

which software do you use

peut on choisir le coté prioritaire

Nice video

Now your just confusing me

Nice

thanks for the tutorial 🎉..Wel how can I adjust the angle of the fan? I want to increase

wonderful! 🎉

Why wear gloves when it's all de-energized? 👎

Hi, I am an student of electronics and will need a help in building a system where a CIU can be monitored by a means of a GPS tracking device. This device can also cut off or switch on the CIU in case of an attempt to bypass the token recharge process. Using a simple input and output devices, your contribution will greatly be appreciated.

Wrong inviter contact to the controller charge

bhai ye video banane ke liye aapne konsa softwer use kia he agar aap bata pao to aapki meharbani

hello can i use this to run 12dc leds and do you have a components list i want to power an actual set of 1960s traffic lights for a man cave cheers chris

Please make a note what is data and what is 24 volts please used other devices that used 24 volts with a different pen so we can understand the difference between data and 24 volts all the video i have seen its just data wiring tanks alot

where is the supply of timer

Ролик, блять, для, дебилов. Но дебилы не используют сигнализации. Просто украли 2 минуты моей жизни.

am using this setup. My problem is that one controller is working the other doesn't when both Panels are connected. one 300W P & one 300W M. If I switch off one Panel, 300WP, the Charge Controller on that side works. If I switch that one off & the other, 300WM, on then that Controller works, but they won't work while connected together in that configuration. Why? any ideas? Both 40A EPEVER CC's. That feed into a 300W LiPo4 Battery then into a 8000/4000W Inverter.

wrong

Turn the music down

Thanks for the advancements, keep it up

This is really really bad. The video shows the connections but DOES NOT SHOW TERMINALS. If you don't show what terminals you are connecting to i.e 85, 86 etc then whoever follows this will likely blow up what they are wiring. A good video made useless by 1 mistake

very profectional engineer

🎉🎉🎉❤❤ i love it

Very nice❤❤❤❤

Very nice❤sir

Makasih Bang Ilmunya

Led esta ligado errado!!!!

make no sense, 2 me

Good work 👏

draw the design using what application?

Nice digaram

Thnks for the videos im so satisfied to watch your tutorial sir...👍

sir ,its very clear and easy t o understand👍👍👍

Is loop isolator same as control module?

Diagram please

👍👍👍

Super

Simplesmente não vai funcionar! Circuito está adulterado 😮

O source não é ligado ao negativo? Dreno e source são positivos, sou leigo bo assunto, poderia explicar melhor?

I try this setup and i used different controller and different variant of panels .. my solar setup loke this is.good.proper wire sizing and DC breaker

L और N मतलब?

Insightful and educative, but how do one take his load point from.?

Just the video I've been look In for to do a wiring job in my basement thanks👍

The indicator's one end with resistor is correct, but the other end should be conneted to the opposite end of Thermostat. Then only it will glow only when thermostat is ON.

wrong schematic because the drain is connected to +12v which mean we have a n channel mosfet so the configuration must be low switch which mean that the load must be connected to +12v (serial with drain) and not to 0 v.

dc or ac

Bro, what software do you use to edit this kind of video, please give me the link of that software, I also want to edit it, bro.

Bro, what software do you use to edit this kind of video, please give me the link of that software, I also want to edit it, bro.

Bro, what software do you use to edit this kind of video, please give me the link of that software, I also want to edit it, bro.

Awesome. Awesome video. If I wanted to add this ATS for a home running 220v (2-110v legs) with neutral and ground, along with a generator that is running the same, how many input/output would I need on the device?