Відео

Ya put them on and use a insulated screwdriver to see how far the spark go from one to another , as soon as the burner comes on

@stocharron2753 there's no springs on AFII transformers

@@Allcoastlawnandpressurewashing yes you can. We used to use them but found ag hose to last longer and leak less

@@danpowers1551 the bucket had 12.5 percent SH in it. Not diluted

Thanks for watching!

@@rudyboy2010 thanks for watching! Today I’m going to make some truck washing videos.

@@dramaface it’s about 1.5% on the application

@ okay, but is the bucket/tank you’re pulling from with your injector straight SH, as in not a diluted mix?

​@dramaface yes thats how that works dude. You pull straight sh.......and your injectore dilutes it down to 1.5% or 1% or maybe even 2% depending on orifice size gpms / pressure....

@ I’m pulling from a drum that has 12.5% bleach

@ thanks man!

@@soundgod8380 about 300

@@JuanOcanas-fv8wf more than likely the spray pattern is not igniting entirely or dropping while it’s running, you need to find out if it’s the fuel nozzle.

@ ok I th al you very much sir , I will be reaching out to your shop out in Kemah sir

@ we closed our store down. We’ve been sending everyone to Pedro at PWR in south Houston. We are just a wash company moving forward

@@TXcommercialwash ok sir thank you very much for the information and have a blessed day !

@@ASH12B 3500 PSI 8 GPM Running a 21 inch mosmatic with a 3 tip spray bar with 2.5 orifice nozzles.

We are considering an acid treatment to seal the deal!

@@TamilLatest 3500

@@TXcommercialwash that’s pretty hard-core, could I get away with 1500 or what do you think the minimum is?

@ 1500 works for most things just runs slower Gpm is where the speed really comes in For what we do I like to run 3-4k psi on our flatwork Residential I’ll do 2000-3000 depending

Thank you for watching!

@@TheMatthewDMerrill do you have the electrodes angled right? There is a tool with replacement electrodes it looks like a silver comb (kind of). Use that to position. It is possible the fuel is not landing on the spark. If you have spark and fuel, you need to find out why the fuel is not making contact with the spark.

@TXcommercialwash thank you for the advice, I got it off and tested with it in the open, no fuel was coming out the tip, maybe clogged or something. Am working on it now to see if I can clean or just replace

@ see if the fuel pump is siphoning. It is self priming so you should be ok to pull the hose off of it and stick your thumb to it. If it is sucking then you have a restriction between the fuel source and the fuel pump inlet. I’ve had dead insects clog my line before.

@@TXcommercialwash well I just saw your comment after I finished, but it was indeed the tip being clogged despite having that weird metal filter I've never seen before in anything else. Opened up the tip and didn't see much at first but I realized there was another part that could be opened on it, I did that and cleaned there as well, after I could see a very small light coming through the hole, I put the pieces back together and tested it without the electrodes on and it started spraying oil. I put everything back together and all is good. Thank you for the help!

@ you’re welcome! I’m glad we could be of help.

@@JuanOcanas-fv8wf thank you!

@@JuanOcanas-fv8wf it depends. Anywhere from 40-150 depending on a lot of factors

@@chevygirl5165 I wish I could help, Fred retired September and he is the burner wizard. We are no longer servicing equipment after his retirement.

Then you go back further on the electric to find you problem

@@juniorbiel24 we Siamese the exact same specs. The lower psi will be dominant. If it’s a 4000 at 5.5 and a 3500 at 8 for instance your pressure will be in the ballpark of 3600 psi flowing at roughly 13 gpm We have found at 13 gpm you can still Siamese with 3/8 all the way around. If you Siamese 2 8s it restricts flow unless you have half inch pressure hose coming out of the outlet of the Siamese.

@@TXcommercialwash I appreciate the response back! Im glad to know you run the same exact specs. Excluding the psi. My 5.5 is at 3000 i believe. Im glad i found this video because I have received mixed responses from other supply companies. Im assuming you have been siamesing those two units together for years without any issue, correct?

@@juniorbiel24 this is correct, I’ve had about 4 different Siamese combinations we have done and we have been since 2018

@@TXcommercialwash sweet! I appreciate you

@@NowYouKnowMoe if you’re asking that question, just wear rubber gloves to be safe.

@@TXcommercialwash I just decided to buy a new ignition transformer because the one I have is like 25 years old