Відео

Good job thank you for shoing it to us😊

I change mine. Don’t need to jack up the car

This was super helpful on my son's 2011 328i Conv. Thankfully BMW upgraded to long bolts on the holder which made it easier. Thank you for posting!

wrong key fob

Hello could you please help me to know the part number or where did you bought it?

Awsome. Got 2002 vtx 1800c and will prolly need to do this sometime soon. Thx man

Never trust anyone who doesn’t use Jack stands. It’s your dangerous having those jacks under there like that and not using stands!!! Please be safe people!!

When you replaced the front brake rotors did you have to remove the brake caliper carrier? Thanks

Is your Transmission still working and holding up since using the Lucas?

How do you fix the trunk tho cause I have power it just won't open

Hi, link for buy part, thank.

Awesome video thank you for posting 👏👏👏👏

Good job and thank you for taking the time to share your knowledge.

I’ve been hearing to clean everything including the slide pin needs to get cleaned and greased, also any moving parts with grease.

Is this the same process as a 2009 acura rdx??? Help !!!

straight to the point and informative. what. a. guy.

is there anything special to inflate tire. can i just go to any gas station and fill up with air to reseal the bead

What is the name of the cover

Working on an E93 is a totally different monster. I could not remove the trim panels in the rear to replace the shocks. I had to throw the towel. I did replace the battery but it took me 1 hoour.

Awesome video. Thanks

well done mate. thank you habibs

When you say bracing the breaks when you turn the tire does pressure need to be on the break pedal while the tire goes on?

Didn’t put the filter in on camera

Thank you - helpful real time video of the awkward job this is. Thankfully my first battery lasted 13 years

I bought a used clock spring I will be replacing my old one, what is the yellow clip you removed? What was its function? Will I run into issues ?

Typical bmw not even a battery can be a simple replacement

Having watched nearly 50years of both factory and aftermarket "how to videos from Ford, Gm, Chrysler, and even at the beginning of my automotive career AMC " You are by far the best instructor, pointing out every aspect of the operation in easy to understand instructions.

Disaster

The sound is terrible

Any idea why the blue and red wire is not hooked up mine is also not hooked up but I'm having my airbag and seatbelt light come on. Awesome video!

Good video thank you i love you

Thank you for all the details, especially the screwdriver trick to remove the plate, very much appreciate it👍👏👏👏

Do you have the part #?

What is the part #? I need to replace mine. The left blinker does not stop on a left turn

Great video, saved me a lot of time with the difficult bracket, thanks for posting.

Thanks for the video bud

Thanks 👍🏻👍🏻

How do you feel about using a gasket instead of RTV when replacing the pan?

Amen to “nothing is ever simple”

what is the torque spec for hrv 2020? is it the same or different all whell drive please reply

You mentioned different noises for a bad pump versus leaking o-ring (if I heard correctly). How do you know? Mine is whining but not as bad as yours.

Great oil. Get rid of the lucas crap.

04 Acura MDX Car thinks door is open when closed. Replaced jamb switch, still doing it, but dome lights dim and anti theft engages. Door open is still displaying and light bulb on driver panel is on. If I remove the bulb dome lights come on and anti theft will NOT engage. Ideas?

Damn thank you man.

I had the same problem. I replaced the electrical sub-harness that connects the driver side door to the harness by the fuse box next to the parking brake under the dash. Post pandemic, Acura had run out of this sub-harness. I waited one year for it to be in stock again. It cost me $80 and took less than an hour to install. There are videos on UA-cam that demonstrate the installation. Tip: The opening between the door jamb and the cabin is not easy to see. You have to route it through the opening with your fingers. When removing the old sub-harness, I tied a long shoestring to one end. When I had removed the sub-harness by pulling it through, I left the shoestring in the opening of the door jamb…one end in the cabin by the fuse box, the other end hanging in the opening in the door jamb. When I was ready to install the new sub-harness, I tied the shoestring to one end and pulled to through the opening…with a lot of feeling around with my fingers. It made it easier to do.

As for as the putting the 10mm hex in the rear diff fill and drain plug. It is always good to clear the rust with flat head screw driver or with a pick then tap your 10mm hex there with a hammer. 10mm hex should be all the way in the hole to avoid stripping it. If 10mm hex is all the way in then chances of stripping the hex nut is very low. Key is to remove the rust from the hole and tapping the 10mm hex key into the hole to make sure it is all the way in then open it loose.

thank you so much for the video - great work. There is front differential as well. It takes 14mm wrench for both drain and fill plug. Fill plug of this front differential is at such a awkward and tight spot that you can't even imagine it being there. There is not enough space for a socket and you can only use wrench. Room to turn the wrench in that tight spot is so tiny that Not all 14mm wrench can work there. 14mm made by Stanley worked for me but made my Moto Master did not. Once you loosened the fill plug, it is easy to take it off with two fingers and there is only space for 2 fingers nothing else. Please have a look and you would be really surprised. This video ua-cam.com/video/mVlxfN0eOrs/v-deo.html helped me to get the front differential fluid changed.

Legend brotha

Why won’t windows work and blinker after replacing?

Very helpful steps to follow; however, you have to deal with a very heavy battery. Lifting the battery in and out was the hardest. Do not try if you can not lift heavy item in a very tight space. Thanks.