Novak Conversions
Novak Conversions
  • 10
  • 821 360
JK cable shifter upgrade install
Purchase link: www.novak-adapt.com/catalog/shifters/jk-cable-shifter-upgrade-kit
The Jeep JK cable shifter works well from the factory. But with time, use and corrosion, the stock cable bushings and retention clips deteriorate and eventually fail. This can leave your Jeep stranded in neutral.
This kit replaces the most common failure points of the transfer case cable shifter.
www.novak-adapt.com
435-753-2513
Переглядів: 4 094

Відео

Novak Tach Emulator Install
Переглядів 2,6 тис.2 роки тому
How to Install the Novak E-TX Tach Emulator. This module adapts the Stock Jeep tach gauge to work with a GM engine conversion. www.novak-adapt.com/catalog/electronics/tj-xj-crank-position-tach-emulator/ 00:00 Intro 00:22 Mounting 00:37 Wiring 01:55 adjusting tach needle 02:39 troubleshooting
XJ Radiator Install Novak (archived version)
Переглядів 3,4 тис.3 роки тому
This radiator has since been updated to a thinner and higher efficiency core. Cutting and custom bracketry for the condenser are no longer necessary. Simply drop our new version right into place. Updated video to follow soon. www.novak-adapt.com/catalog/cooling/radiators/xj
Jeep TJ LS / Vortec Engine Overview
Переглядів 59 тис.6 років тому
An open-chassis overview of a GM Vortec / LS V8 engine conversion into a Jeep TJ and some of the products that make them the highest regarded and most frequently performed. www.novak-adapt.com/
Trail Hero to War Hero 2016
Переглядів 1,9 тис.6 років тому
The rising, three day Jeep trek on historic trails from Utah's stem to stern, starting at the Idaho border and arriving at the Arizona border for the Trail Hero event. www.novak-adapt.com/
Yeti & Yolo TJ Overlander 5.3L Build
Переглядів 56 тис.7 років тому
Overlanders Yeti & Yolo tell their story during their Novak LS / Vortec powertrain install into their Jeep TJ www.novak-adapt.com/
A GM Gen III V8 Installation into a Jeep CJ7 - Hawaii 5.3
Переглядів 157 тис.10 років тому
A videolog featuring the installation of an LS / Vortec GM engine into a 1985 Jeep CJ on the island of Maui, using an integrated powertrain from Novak Conversions. www.novak-adapt.com/
About the SM465
Переглядів 55 тис.11 років тому
Novak Conversions shares our knowledge about the history, capabilities and possible jeep conversions with the SM465 www.novak-adapt.com/ www.novak-adapt.com/knowledge/sm465.htm www.novak-adapt.com/catalog/transmission/transmission_parts/sm465_parts.htm www.novak-adapt.com/catalog/adapters/engine_to_transmission/465_to_amc.htm
About the 4l60e
Переглядів 482 тис.11 років тому
Novak Conversions shares our knowledge about the history, capabilities and possible jeep conversions with the 4L60E www.novak-adapt.com/ www.novak-adapt.com/knowledge/4l60e.htm www.novak-adapt.com/catalog/

КОМЕНТАРІ

  • @Unkownktm
    @Unkownktm Місяць тому

    Hi there, great looking product I’m in Australia and was looking to purchase the kit, but the postage cost I’m unsure of. I’ve sent an email to your business, cheers

  • @rylo_duz
    @rylo_duz 2 місяці тому

    I'm trying to keep my battery in place with a/c. Any recommendation on belt size with the low mount a/c and a high mount alternator? Would save me a few trips to the pay store 🙏 ls3

  • @billbarker3715
    @billbarker3715 5 місяців тому

    I installed this about a month ago and it is awesome. Come to find out my transfer case bushing was totally gone. This is a must have.

  • @mhi7340
    @mhi7340 6 місяців тому

    How can i contact you guys at Novak ?

  • @byronquinley1400
    @byronquinley1400 7 місяців тому

    Installed today. Works with a manual transmission. You need to disconnect the boot from the console. Also (on the Sahara at least) there is a wiring harness that under the console that needs to be disconnected. Lastly the clamp the clamp with the 3/8 nuts wouldn’t tighten up for me. The studs were loose and they just kept spinning. Zip tied it to hold in place.

    • @NovakConversions
      @NovakConversions 6 місяців тому

      Hi @byronquinley1400. If the clamp won't tighten up, go ahead and remove the middle tab from the clamp and tighten it down like that. If you're still having issues, give us a call and we can send you an updated design that is sure to work as intended.

  • @octavio9485
    @octavio9485 9 місяців тому

    Where are you guys actually located? I would love to be able to set it up to get my tJ Done I have one that is super clean. I bought it from original owner.

  • @davidgomez3737
    @davidgomez3737 Рік тому

    Do they all come with ac condenser what if you aint running ac

  • @WhatMeeWorrry
    @WhatMeeWorrry Рік тому

    Does this work with the auto transmission linkages as well?

  • @M7ammad
    @M7ammad 2 роки тому

    Is the one that has dual pass both inlet out let in same side has better cooling than the other one which looks single pass?

    • @NovakConversions
      @NovakConversions Рік тому

      When testing our radiators on our dyno, we measured a 1% efficiency difference in cooling capacity between a single pass and dual pass design. The advantage of either is having your ports on the correct side of your bay for your engine type.

  • @chalinp4886
    @chalinp4886 2 роки тому

    Has Novak ever put a 4l60 e behind a 4.0🍺🤷‍♂️

  • @chalinp4886
    @chalinp4886 2 роки тому

    I have a jeep 4.0 5 speed and 231 j case tj but I can’t operate a manual do you sale components to instal convert to factory 32rh maybe some left over components from viseversa conversions if not can I run a 700 r please help just want to enjoy it I hate manual and I’m not ashame

  • @manthis22
    @manthis22 2 роки тому

    Looks good, but I cannot find the part on your website. Why wouldn't you leave a link for your product to make the purchasing process easier?

    • @NovakConversions
      @NovakConversions 2 роки тому

      Here is the product link manthis: www.novak-adapt.com/catalog/shifters/jk-cable-shifter-upgrade-kit

  • @jeeper2371
    @jeeper2371 2 роки тому

    I once tied it up with a tie-wrap(temporary) to get me home late one night in the woods using the light from a cell phone . After crawling underneath in very wet ground. Then I made a few on a lathe in brass. If your Jeep has the crappy hard plastic ones buy a couple brass ones, and save screaming some very bad words! -(PS change them before you leave the yard because its a matter of time! "!@#@!$)!

  • @ilmjcxj8064
    @ilmjcxj8064 2 роки тому

    Excellent ...

  • @Abourgeois17
    @Abourgeois17 2 роки тому

    Just ordered my radiator and fans yesterday 💪🏾 camt wait!

  • @tke1006
    @tke1006 2 роки тому

    I love to see the full build of the XJ

  • @yerwrng
    @yerwrng 2 роки тому

    A radiator first real nice in the cargo area over a fuel cell .

  • @j.d.mcginn6946
    @j.d.mcginn6946 2 роки тому

    I don't think this is enough cooling for a v8. Not even enough for the stock I6 in Texas heat. I do like to run 170 degrees water temp with outside temp 100 degrees while pulling a 3000 lb trailer with a/c wide open and do this idling!

  • @oscarparedes778
    @oscarparedes778 3 роки тому

    The 3 fans produced 2,400+ cfm? I was told each fan only produced about 550.

  • @ilmjcxj8064
    @ilmjcxj8064 3 роки тому

    Excellent video ... keep them coming ...

  • @RyandMelFam2000
    @RyandMelFam2000 3 роки тому

    Great video guys. Phenomenally clean set up that installs and cools exceptionally well!

  • @michaelbrewer3693
    @michaelbrewer3693 3 роки тому

    The kit you used you guys sell everything need even the compressor? Is that the Lm7/5.3?

    • @NovakConversions
      @NovakConversions Рік тому

      Yes, we sell everything you need to LS Swap your XJ! Give our salesmen a call and we'll put together a custom kit specific for your setup. www.novak-adapt.com/contact/

  • @dorothyshwab147
    @dorothyshwab147 4 роки тому

    You all are awesome, brought a tear to my eyes!!!! You Rock

  • @jessehinton480
    @jessehinton480 4 роки тому

    Don't forget kits for xjs

  • @larrymoore326
    @larrymoore326 4 роки тому

    Cool video guys !

  • @jakedemmer4895
    @jakedemmer4895 4 роки тому

    Wow I learned a lot about the swap... they swapped it that's about it.. stupid video...

  • @Jessica-mq3mm
    @Jessica-mq3mm 4 роки тому

    ohh man, I cried at the sinking yeti part, and everyone helping yall out. We almost lost my brother's fourwheeler by the lake that way. We had to get momma's 91 cherokee through the woods and out to us to save it. I thought he was going to sleep out there all night with it, revving it to keep the mud from sucking back into the exhaust. When We finally got it out, and it was raining mud from spinning tires, and we were wet, cold, and plastered in mud...I never felt so free and blessed racing the sunset home. God bless y'all <3 Adventure on.

  • @dustyak79
    @dustyak79 4 роки тому

    I'm confused am I watching a LS swap video or commercial for match.com/farmers only

  • @siwash99
    @siwash99 5 років тому

    Proof that sliding into her Dm's does work LOL!!

  • @nodayatthebeach
    @nodayatthebeach 5 років тому

    I'm envious of these two !

  • @ATEMOFFROAD
    @ATEMOFFROAD 5 років тому

    Novak is this a Jeep tj “California” edition package you guys all installed? Smog ready? Any detail? Thanks

  • @briansolliday1117
    @briansolliday1117 5 років тому

    What an amazing video.

  • @Jenuin
    @Jenuin 5 років тому

    Wow. Those two. If I could only be so lucky. Amazing build. I'm currently getting setup for one. Selling the sedan. Selling the muscle car. Buying Jeep parts. Maybe I'll meet my own adventure partner.

    • @Jenuin
      @Jenuin 5 років тому

      I'm keeping my diesel truck. FYI

  • @justinhancock1346
    @justinhancock1346 5 років тому

    I thought this was a jeep build not a relationship story.

  • @velazquezjaime149
    @velazquezjaime149 5 років тому

    I put my fuel injection chevy v8 on my yj years back and novak guys where awesome they realy help me with my jeep 👍👍👍 for novak adapters

  • @Matp345
    @Matp345 6 років тому

    Such an awesome company. I pray they start making zj LS stuff.

  • @Bigtoe7272
    @Bigtoe7272 6 років тому

    Spoke to Jeff up at Novak Conversions and he sent me a list of things I need for my conversion a couple years back. Called back this year and he went over the list with me again. And again, he answered every question that I could possibly think of. They offer every thing you need to do an LS swap. Even reprogramming your harness. Real personable and knowledgeable group. From my research, this is the only company I would reccomend if you want your conversion done right and professional! I am now looking for an engine and then I am going to start checking off my list! Can't wait!

  • @adamkalman6011
    @adamkalman6011 6 років тому

    GAY

  • @1187830
    @1187830 6 років тому

    Hey Novak! I'm a 20 year old kid base in North Salt Lake, Utah with a passion for jeeps. I would really like to get an LS3 in my 03 TJ... how much would this cost me?

  • @ZakarooNetwork
    @ZakarooNetwork 6 років тому

    He better put a ring on it! Her finger that is...

  • @SevenSlotSociety
    @SevenSlotSociety 6 років тому

    LOVE this video!

  • @noelopez8206
    @noelopez8206 6 років тому

    My question is who has ownership of that Jeep?

  • @chronoboat11
    @chronoboat11 7 років тому

    I have Not seen a Jeep that sits level!!! Why???

  • @kingtaco5000
    @kingtaco5000 7 років тому

    Do you guys do the lj

  • @southcoastsyndicate3224
    @southcoastsyndicate3224 7 років тому

    Have followed Yeti and Yolo for a long time now, and its great to see companies like this who share the passion for adventure getting behind such a great couple. I will be sure to keep Novak in mind with any conversions I or anyone I know is considering!

  • @HeyItsWinner
    @HeyItsWinner 7 років тому

    Wow coming from another jeep channel this is awesome haha

  • @theashrook6129
    @theashrook6129 7 років тому

    This couple will probably be the main reason I try to stick with Novak when I start my YJ v8 conversion