Відео

Great work buddy 🎉

Screw? Mine is a push button. And you slide off rather than pry.

Good job. So often a mechanic's best tool is "calm & patience"! Calm is a superpower. Patience definition : the capacity to accept or tolerate delay, trouble, or suffering without getting angry or upset.

What is the adjustable socket tool called that you used to replace the rear spark plugs?

Thank you

Torch sir get that bolt red hot

Blades set up wrong!!

Wish I could take my bike to you.

idiot

Thanks for the video, thanks for sharing your knowledge

That’s not a ford explorer. Thats a ford expedition.

Informative

is that from pressure loss?

Ford expedition, not explorer.

My 2022 passport only have 53,000 miles on it,I'll wait until 100,000 miles

What year is this?

You've been phrogd

Anvil gap set wrong... just sayin...

You've just been phrogd

You've just been phrogd

You've just been phrogd

Bro you are a life saver, this video deserves more views. Thanks for the video

Had the exact same break with the hook on my 2010 Q5. It broke when I went in to replace my driver side window controls. Just bought the cable from Audi and will be using your video to replace it once it arrives. Thank you!

You just got phrogd

You just got phronked

I love this cat, he is pretty

Very informative thanks, I think I have this same issue

That’s a single cylinder

That fuel filters backwards

Mine is up down up down left right RT LT

Great one

🎉 keep it up Brother.

At least you tried.

Isn't the cotton supposed to be placed in the bottom?

I have a grinding noise coming out of the left side of my printer on one of the initiation sequences. I want to take the left cover off to see what I can see. This video was perfect. Thanks!

thanks

Hi, I couldn't get my 1/2 in drive, M14 triple square to fit between the frame for the rear-lower caliper bracket bolt. Any tips?

Sister xiaoqiao is a friend who knows cars. 😊

Can you please provide a link for the tool you use to lock the cam shaft?

Where did you purchase your parts, I got some aftermarket parts that don't fit and I went to the dealership and still won't fit. I've spent over $400

those back three scared me after seeing this video but if you take your time and use a bunch of differeent extentions for your swivel socket wrench it it's do able just don't rush. Thanks for this and subbed

They work better than any other trap I've ever tried.

Thkx for the detailed video; I had the same issue for a few weeks; the error code reported a faulty FCM (Fan Control Module) which meant replacing the entire unit with both fans and was upwards for $1400.00….I keep driving for a few more weeks and then spent 1/2 day t/shooting the issue; when I got to the connectors (u have to remove the undermount protection), i took a carefful look at the cables and found a single cable that was almost broken….i fixed that and issue got resolved. Maybe lucky me but I wonder how many people have had a similar issue. I would suggest before u do anything, check the connectors and make sure u don’t have a broken cable. All the best.

Love the video. Simple and to the point. 👍🏽

What brand and were from?

Yours is a chipper with the chipping blades on a drum which feeds the brush material through one pass and then out. It leaves a lot of the material only shredded and not finely reduced. I would be very dissatisfied as well with what materials you ended up with. What you want is a hammer mill type shredder chipper. It has its chipping blade on a heavy flywheel where you feed the bigger limbs, say 2 1/2 to 3” through the side chute. The smaller brush goes into the hopper at the top and then the hammer mill flails shred it up. There is a curved metal piece with 1” or 3/4” holes that keeps all the material back, including also the material that the chipper section chipped up. All this keeps going around getting shredded finer until it is small enough to fall through the holes. I used a shredder chipper that was built like the description and it was a MacKissic Mighty Mac 12PT. With it I cleared up all the brush and limbs from about 80 trees, mostly white oak and some firs. It was a lot of work but I was impressed with how small the pieces were that it all reduced down to.

muy buen video, llevamos años con este problema

Awesome, I like short and direct video !

P r o m o s m

Can you please provide the pump you purchase the link?