Відео

In this video's thumbnail, the first circuit board is osd and that black and red cable is used to connect the osd to camera the camera have osd port that connect to that wire and the other end of that wire will connect to osd

Thankyou!! Elrs module is built-in with AIO and i uploaded the video on it here is the link : ua-cam.com/video/Ag0VBOxTBOU/v-deo.htmlsi=Z5IjPJbi8TBrhA6s

Thankyou Bro!! 🙌

You're welcome! 😊

Thank you! 😊

Programming is mandatory but I didn't shown, because video is already too long so I will upload part 2 of programming this drone soon.

Betafpv VR006 It doesn't have inbuilt dvr I have recorded it with external receiver.

@@aerofuture53 ok thanks

Welcome ☺️

Thanks bro! 😊😊

DM me on Instagram:- burhan_k_marfatiya

It can lift upto 1kg payload. I will make a video on it make sure to subscribe!!

Thankyou bro!! ☺️☺️

I think this is happening because your Escs are not connected to flight controller properly, if the problem doesn't solved then message me on instagram id: burhan_k_marfatiya I will definitely help you!!

Thank you!! Bro!!😊😊

No the Vtx , esc , expresslrs receiver, flight controller this all is in one board (AIO) I am using Neutronrc At32f435 mini 2s 12A AIO so if you want to add external vtx then you can but this board also have inbuilt vtx

@@aerofuture53 Do you know of any such similar boards,because this one isn’t available atm..

Sorry bro but I don't have idea why it is not available right now and most of similar AIOs is also out of stock, i got this board from my friend, when he went china, I told him to purchase it from their

@@aerofuture53 Thank you for the effort,may we all have good Aio’s in the future!!!

Welcome! 😊 And sure we have new AIOs in future and if any AIO will become available I will sure tell you.

180-200km/h with 6s lipo battery

3aeolus 10000kv and 1hglrc 10000kv brushless motor

@@aerofuture53 thanks 😍😍😍😍😍

Welcome! 😊

Yes bro you are correct, and I have helping hands but I am making videos for my viewers and subscribers who don't have helping hands and confused how to make perfect solder in XT60, that's why I have made the video without using helping hands.

I have custom build this drone, i have purchased all parts as my requirement motors of hglrc 10000kv and Neutronrc AT435Mini 5 in 1 AIO and Radiomaster Pocket Elrs version and betafpv vr006 fpv goggles and the main camera from where I shoot in 1080p@60fps is runcam thumb, and if you want to purchase the parts of this drone then you can purchase it from betafpv official website because in India it's hard to get Pavo Pico parts offline and I purchased the frame and AIO ,battery of 450mah 2s from my friend and runcam thumb , fpv camera runcam nano2, 45mm props from robu.in and fpv goggles from insidefpv

Thankyou!! 😊

Thankyou bhai!! 😊😊

For what purpose?

Yes! it is possible but the flight controller I am using is all about in one. Means it have inbuilt expresslrs receiver,4 esc , analog 400mw vtx. You just have to solder 4 motors and fpv camera and that's it. And if you want to use your own receiver then you can use it by soldering it on that flight controller for external receiver pad and it have analog vtx so it will easily connect with your Eachaine Ev100 goggles. But if you use the external receiver then it will be more heavier so I suggest you to purchase expresslrs radio controller like radiomaster Pocket Elrs version or radiomaster tx12, radiomaster tx16 or radiomaster boxer. And the flight controller I am using in this drone is neutron rc AT32 F435 , 5 in 1 AIO.

Hi, it’s me again 😅 I tried and built the drone exactly like yours, but now I have some problem to make it flight correctly, as soon as I arm the motors it starts going crazy and wobbles. Have you encountered the same problems or with you everything went smooth? Is there a way to fix this with betaflight? Thank you very much

​ @lucu1911 ​yes I have encountered the same problem when I made it for first time here is the solution : connect your drone to betaflight and go to motors tab and enable the options to run the motors while connected to betaflight and then take the master key at top position and plug in the battery and after Motor beeps complete then lower the master key and then run all the motor using master key and after doing this steps enable motors direction is reversed option and save and reboot and then try to fly drone this steps I followed to solve this problem and I wish it work with your drone also and if it doesn't works then message me on instagram id : burhan_k_marfatiya and I will definitely reply you!!

@@aerofuture53 thank you very much, it was the only thing that I didn’t do, I will try and see if this will fix my problem

Sure, try it and if it works then comment here and if it doesn't work then message me on instagram id: burhan_k_marfatiya I will definitely help you 😉😊

Yes! no problem

Thankyou! 😊

Whole setup Around ₹35,000

Motor k sath jho cap ata hai vo lagaya hai

@@aerofuture53nahi bhai ap shayad zip tie se lagai ho

​@@pyro_boy137 ha bhai vibration ho Raha tha cap se isliya zip tie lagaya hai

Thankyou bhai!! 🙌🙌

Yes, I didn't selected because I am very excited to fly this little guy, so I just made it and did the setting which can just make this drone fly. I will change it soon! Thankyou!

This video is taken from the external receiver which have stock antenna that's why it have a bad signals but in the goggles I have a nice signals with no problem and at other side you are correct I have to switch channel or select vtx power which I haven't did in betaflight.

Yes! In ready made betafpv Pavo Pico kit the DJI O3 module which is digital is pre installed, but it's expensive and I have custom made this drone with analog camera and vtx and different parts so it's analog and it's affordable and as you know that analog camera doesn't give that quality to record some awesome footage so I have mount runcam thumb on it to get better footage.

I am using 2pcs of 1s happymodel 300mah by combining it togather and make 2s lipo battery so it gives around 3minutes of flight time but if you use betafpv 2s 450mah than you get more flight around 4 to 5minutes

Runcam thumb 1080p at 60fps

Thankyou bhai! 😁☺️☺️

Try downloading this app👇 apps.apple.com/us/app/fpv-go/id1461701628

Yes , I think it is clone but it is working well and good . I purchased it from offline store but you can purchase it from robu.in it's same product. I have used 2200mah lipo battery to charge in this video , by following this process you can charge any other lipo battery easily . I am using 2200mah lipo battery for my Quadcopter drone and it gives 5 to 10 minutes of battery backup, I am using it from 2years and I have purchased It from offline store but you can purchase it from robu.in orange lipo Batteries that batteries are better than this battery

@@aerofuture53 brother... currently it's not available in robu... U can check the serial number on the backside of the product. I am sure this one is a clone.. If u had bought it for above 2k u got fooled. Because og available for 3k(dc one) And for AC v2 around 5k

​​​@@farhanfaiz1998the serial no is there on the box, it is CH-9-0006-S I have purchased It around 3.5k, it is available at flyrobo.in at 2.7k

Camera supports upto 5 volts maximum and, video transmitter (vtx) supports 7volts to 27volts maximum

Kya problem aa rha hai

Take of nhi ho raha left or right ja raha hai

Age piche ho raha hai Please Hamara madat kare

Ap mujhe Instagram pr DM Karo id : burhan_k_marfatiya

App name is "Go FPV" you can find it out on Google Chrome, and for gps position you have to connect your camera and vtx to your Flight Controller and select gps altitude and latitude in your osd options in betaflight , so it shows the position of your gps but it works when you have installed the gps in your drone

Thankyou bhai! ☺️☺️

The app name is "Go FPV" you can find it on Google Chrome

@@aerofuture53 Thanks! unfortunately for me it isn't compatible with my phone because I have a newer version of android apperently. Appreciate the reply anyway!

It will works in new version Android devices I am using it in my redmi not 12 hyperOs and it works well, you can download and give permissions and ignore the warning the app gives and connect your receiver to mobile and it works. If not the leave a comment i will reply. @@elliottraymond3274

@@aerofuture53 Unfortunately it automaticaly launches into the google play app from chrome and sadly I can't see any button to download on the google play store app preview page. It may be and android 12 thing (samsung galaxy s10). Do you know of other apps that work similarly?

Hey bro I found a link may be it helps you to download this app note that you can't click on download from Google Play store click on the button given above the download form Google Play button Here is the link: go-fpv.en.softonic.com/android?ex=RAMP-2046.2

App name is "Go fpv". But if you can't find it on Google Play store then search it on chrome.