Відео

Really impressive guys! Cant wait to see the upgraded version. Very inventive and cool design!

i do not know how this doesnt have 3945821093 views. lmfao boy you got me good

Raketen bauen ist eine Kunst die ich auch noch nicht perfekt beherrsche aber einfach weiter üben

😂😂😂😂😂😂

Wow

burn rate is way too slow, you should test a new propellant formula and maybe use metal powder to make it work

always wanted to make a diesel potato cannon that works off of compression instead of heat but every time i draw it out it ends up way bigger than i want it be

this is pretty sick, you're a really innovative guy

May need to make the nozzle just a metric smaller with the fuel you are using, may decrease burn time but it will put out a good ammount of thrust

That was a good run dude

What ratio did you use for kclo4 and hexamine

nice one, works for me. :D , let's line up.

You mother effffer scared the shitdangos out of me at 4 am 🤣🤣🤣🤣🤣

hexamine + nitration bath = ?

Yo Wut is the key element of that smoke production ?

Tazer?

Yoooooo how am I the only one to comment on this you scared the snot out of me dog I was like bro he found the hack

yeeeeeeeeaaaahaaaaaaawwwwwww

what plug u used?

Hi! If your interested in using plaster Paris as a nozzle, I recommend checking out my channel. It’s all about test firing rocket motors with plaster Paris nozzles and end caps. I have done 1 inch, 2 inch and 3 inch rocket motors using this method. TIP: next time, put in the plaster directly into the metal tube you are using, so there is no risk of it popping out like it did in this video. Im currently finding out solutions for making the plaster Paris stronger,a and a few solutions I found was using glue and ash to create a higher density and less brittle solution. Im currently creating a 4” diameter rocket motor using rocket candy as fuel, a cardboard shipping tube that is 0.15 thick as a insulator, and a Aluminium 6061 T6 tube that fits snuggly into the other tube. The Aluminium tube keeps the motor together from rapid disassembly and holds the psi. I will be making a video on it soon. Good luck!

Very good what was the rocket mix ??

A work of art!

difficult to get chlorate in the air. I liked it very much!👍

Dude, how did you build that? I want one!

Platinum cell or graphit?? 🤔

Maybe try plaster or kitty litter with waterglass/sodium silicate? That should be strong, heat resistant and bind well. Try making some cuts in the inside of the tube to get better adhesion with the nozzle assembly too.

nice stuff, good luck on the next run

Hexamine/Urotropin + Hidrogen Peroxide/Acetone + Citric Acid= HMTD Hexamethylene Triperoxide Diamine.

It's a firework

What is your ratio? I've been experimenting with zinc and sulphur. Also, are you constructing nozzles or pre made?

Are you sure you need that much power?

I've done some recent testing with clay and grog nozzles in APCP motors and found that mallet ramming doesn't work very well, if you don't clobber the absolute crap out of the rammer and have something to keep the case from splitting they erode pretty badly, but I did find that adding a small amount of epoxy (clear casting resin) dissolved in acetone helps a lot with that and rams a lot more easily, it seems the epoxy helps with the flow characteristics and locks everything together. I added about 10 mils of clear epoxy resin dissolved in 10 mils of acetone to roughly thirty grams of clay/grog/paraffin nozzle mix and stirred the crap out of it, then did a few cycles of heating until the cup was hot and immediately putting it in a vacuum pot (a $60 ebay pump works fine) to remove all the acetone until the smell was gone, then rammed it with a lead mallet followed by clamping it tight in a bar clamp while it cures sitting over a heat gun. The result is a glass smooth (as smooth as your rammer anyway lol) rock hard nozzle that seems to erode a lot less with a smoother internal surface. I'm going to experiment with adding graphite to it as well, a moldable graphite composite nozzle would be amazing.

im trying to make a chlorate cell but i am a newbie is 6volt 7.5amp good?

Very cool and makeshift :) How much did you get from it? Just one thing though, the electrodes are suuuper far apart here, I bet barely any current is getting through. Make them a little closer to make the cell way more efficient.

I've been playing with melt cast ammonium perchlorate/hexamine lately, it's amazing how much power hexamine can provide as a fuel. I like the flames and sparks that comes from burning loose fuel, it's quite pretty. That looked like a great burn, and like everyone else has mentioned a burn rate catalyst will take these rockets to the next level, 1-2% red iron oxide is a good place to start.

how can o avail clay wax for whistle bomb nozzole

I guarantee you its detonable but it would take much more impact than that, Id watch with the level of confinement you give it because DDT is a potential concern; other than that I dont think its that unsafe

a flyback transformer (easily obtained from old CRT TV) would work much better as an igniter

Do a bleach and ammonia one next!

long burn duration

Thanks for making this video, I subscribed, keep up the good work

Nice video

For those who want to know how I made this.ua-cam.com/video/K5UI3Z65Y_0/v-deo.html&ab_channel=ToastyG

Can you send me a video of how you made this, I make sugar rockets, I am assuming it must be pretty similar. Thanks

I think you need to add grog with you nozzle mix.

Potasiun clorate is he burner rate so high,because is a explosivos compound,add litlle bit of sodium bicarbonate for slow down the fuel and prevenir catos.dont pound whit hammer because very sense that mix.

Great. Now the earth has been knocked out of its orbit...

Nice ... great idea

what exactly is the formula