Відео

Merci beaucoup ❤❤❤❤❤❤❤❤❤

Could also be a blown head gasket, Not uncommon on Briggs engines.

Why did u take all the other stuff off of it was just a pVC cover ? Flywheel off why ? Don’t understand this

Fiskars StaySharp Max Reel Mower ua-cam.com/users/postUgkxTPN04aT-Qdjr_KS3ql7ng8wnU3wwsCqk also recommend This is what all push mowers should strive for. It was easy to push. It cut the lawn. The blades are sharp, very sharp. The one minus that everyone should be aware of is you need to be very careful taking the cutting unit out of the box. There’s a plastic guard so you don’t cut fingers as you take the main unit out of the box but it’s not taped down. As I took the unit out, I ended cutting a piece of my shirt. The plastic guard moved and my shirt touched one of the blades.

Did you just clean the drain holes or did you replace the entire crankcase breather assembly with a new one? THANKS!

##awre## ##JustSaiyan##

well, this looks like a bad design. would be more intuitive to make them bottom out (which most of car does)

Easy fix

Good job

bad job very bad job. you need to do it right and experience,

I am watching yet confused, at 8:55, are you removing excessive oil from the engine ? Was this possibly the true problem to begin with? You then immediately check the dipstick level twice thereafter.

Love the paint!

Very good info, thanks

Good video, I never would of thought a mower has a PCV

Find out that I overfild my lawnmower with oil, helped me a lot, just to tilt and take out amount that was to much in lawnmovier, startet from first time, without filter, I watched it more for leaks from air filter housing but it was 👌.basically like in this video ua-cam.com/video/E93phoyAfSw/v-deo.html

I never even thought of this... I thought it was carb needle and seat. I took carb off and checked needle seemed out of place. I will check that pvc valve. Its a old Snapper hat was in a lake for a day. I got it going. It works but today it was shuddering . and gas was in the oil crank case. I checked compression its at 40. But who knows. I have gotten mowers running with 30 psi

Where did u buy the starter from?

How did you clean your pvc valve?

Thanks very good 👍🤖

Thanks a lot I did not know the operation of how to put this together I checked mine while I was in the midst of assembly and at least three of my valve stem seals had moved out of place!!!

Great video and helped me a lot.

That symptom of blowing white smoke is typically (not always) the crankcase being overfilled. I just got a Craftsman 675 (190cc) 3 weeks ago with the same symptom. The crankcase should have 18 fluid ounces of oil and in the case of the one I got from the curb it had well over 30 fluid ounces. For me I drained, refilled with new and power washed the engine. Runs like new and no more white smoke. Good job on your repair.

Good information, thanks!

If its caused by tilting without top dead center the piston it allows oil to get into the airline. I learned this 30 years ago. Just my observation why not clean the machine before putting it back together? Glad you showed the pcv that mostly nobody ever shows they just show carb cleaning.

Can't hear it!

Is all this really worth it?

👍👍👍

The closed caption is fantastic on this. Lots of music and applause.

I watched this and told myself: time to buy a new mower!

You are the man! After the twentieth screw I was lost

To start with this comes from several reasons. First people tilt their mowers which is wrong which makes oil leak where it was not intended to go. Mowers should only be tilted back on their handle. If you tilt the engine you will have these problems. In some cases oil can fill the piston chamber making it in possible to pull the cord.

Very helpful and easy way to change the valve stem seal.. so far I got a doubt about hammer or not at the end I followed the way on this video and it’s made my work super easy and its amazing. thanks a lot..

Great video detailing a process not seen much from my perspective. Thanks for sharing!

Great job but I don´t have the mechanical skills to go that far. My options now is to get someone to do it or trash it. Thanks

Is there any easier way??? Instead of removing everything i feel like it is over my head. Thanks

That is the possibly best video about oil leaking. I have the same mower with same problem. However, there is some missing part at 6:28. You removed the screws and then what you did there? Did you use a gasket maker? Can you explain, please?

Amazing I have the same issue. What is the part number for this piece, or how should I clean it out?

I wonder if you put some seafoam or atf fluid in the oil if it would unplug the pcv hole?

I'm going to try this ...if it works...you are a life saver