Відео

I don’t have spark on any plugs. Anyone able to help?

Will a broken CDI ground wire/wire bolted under the flywheel affect spark if it got cut by the flywheel? My 1986 8hp 2 stroke yamaha wont start up or produce spark. And when it did before 1 spark plug zaps my finger on the rubber cover and the other doesnt. What does that mean? Its my first outboard and want to know more to repair it.

Did the coil fix it. I gotta similar issue

Nice video! Do you have the part number for the rubber seal and the cap on the pick up tube?

Hey Bryson, did you end up changing anything? Having the same problem on mine as well. Spark is so random!

i got the same buggy but with water cooling

It's been 3 years, how is it holding up?

Has anyone had trouble getting the clamps back on (just like they are when he opened the box)? I think my cables are a bit short.

Thank you very much mate

Lmao yall burnt up the motor it had mud in the water hose 😂😂😂😂

Isn't it supposed to be pumping out water? How good do you think that impeller works after sitting for 40 years. Replace it before you run it ANY more...burn it up and good luck finding parts otherwise I'll last forever.

I had one just like it in the late 80s early 90s . Good little boats. The engines are very easy to work on also. My boat had a 90hp mercury on it . Good skl and riding boat. Good luck.

Yes! Save that boat!

Woow I just bought my self one be arriving in 3 days.. am also thinking of getting the 770 just to have the pear hey never know when u or someone else might need a boost.. hope I made a good choice

Where do you bought the engine ?

My points were bad on mine.was not getting spark on #3 cylinder

CIAO. IL CAVO DI ALIMENTAZIONE CHE PORTA LA CORRENTE DALLA BATTERIA AL MOTORE, YAMAHA 200 CV V6 2T. CHE DIAMETRO DEVE AVERE??? GRAZIE

has the yammy been a good motor? , I have to do the water pump on my 2008 some models had a bracket that had to be disconnected for the shift linkage, but I dont think my year has that.

Keep it up! Previous videos on Yamaha water pump saved me a huge headache looking up parts. Awesome videos!!

How many hours were on old engine before valve head issue? Jw I'm having to replace a 2021 engine cuz of forgotten oil on someone else's part haha. Putting a stock replacement in. Nice video, good stuff

Just replace the ground and it should be fine.

Weld but dont weld machine 250 just buy some cheap stick welder

where is the wave washer spacer chip houseing

Bryson, great videos I am putting a 500 cc in my buggy. I was wondering if you could help me out a little bit your wiring did you videotape you doing your thing with that? Maybe you could help me out a little bit let me see what you extended and everything it would help me out a lot Thanks, Bryson.

Thank you

adjust that air screw....1.5 turns out. That's why its not idling. But this is an old video so I am sure you figured it out.

How thin metal can this machine weld?

Not sure where your located have a good 250 ninja engine laying around if you still need one. I'm in Missouri

Does the windscreen add on help with the wind buffeting?

sync your carbs, there way off

What kind of grease are you using?

Can we have a update on the ninja 250 buggy

If I'm not mistaken it's 10 minutes between each coat and 30 minutes before you can touch it. Either way how did you like the final result?

No grease on impeller, the grease will melt and coat the inside of the engine and will attract sand, dirt, etc. Also, turn the housing as you fit it will bend the impeller in the correct direction

Can we have an update on the ninja 250 buggy

Great vid! Starting to get into TIG and wanted a multi process to get some practice at home . Haven’t heard anything bad about these. Going to pull the trigger then after upgrade to an everlast🤟🏽 new sub

make it look easy, but it isn't even close to easy. have put housing over impeller turn shaft ckockwise and still impeller blades don't go in the housing.

It's a dirt bike. It can handle the high rpm's. Stand up up and ride

Nice work. I just bought a Center Console 21 foot. Probably need to replace the impeller on the 1998 Yamaha 150 2 stroke that came with it. Don't know when it was last replaced. Probably never.

what size breaker on the 220 outlet do you need? manual isn't very clear I see 220V @ 30 and 50?

valves are only like 10 bucks but u got money to blow lol

Bryson Ravenelle, would you vave the link or .pdf for that famous Ninja wiring

OK...30 seconds in and I hit stop button...your background "music" F N SUCKS

is that a carter talon 150cc frame

I missed the neighborhood

U want to sell

Have you heard the good news of Jesus Christ? The good news is Jesus Christ died for our sins according to the Scriptures, and that He was buried, and that He rose again the third day according to the Scriptures. (1 Corinthians 15 1-4) For by grace you have been saved through faith, and that not of yourselves; it is the gift of God, not of works, lest anyone should boast. (Ephesians 2:8-9)

Who makes this cart?

Good pisan 👍👍

Nice job on the review. Pure chinese junk. Mine was no good out of the box. Pressure gauge only reads 30psi. I don’t know whether I have to much or to little air pressure. Arc goes out after a few seconds. Yeswelder is putting unreasonable demands on me to fix it.