Відео

Hi Wayne, that's an amazing bit of kit which should save on waste and make it faster for body shops to mix the paint, I was surprised as to the small mixes it can do which is very difficult by hand to get the mix accurate, do you know if you have to load the tinters in the machine for each mix or does it hold all the available tinters then select them as needed🤔 Looking forward to seeing this being used in your shop Wb🤭😂I laugh but maybe you will get one🤔🤷‍♂👍

What's the name of the pad? Is it a ShineMate pad?

De beer products too?

Did you have the 3M PPS 2.0 adapter P/N 26127 S31 Type on that rig?

What a fantastic place Wayne you are so lucky to have the chance to go there, it was such a shame we had the sound issues when you was demonstrating the VR spraying thingy (sorry not sure what it's called😁) but it didn't take away from how amazing it is I would like to try that out as it's an amazing bit of tech👏👍

Nice video mate from Kiwi

Сколько стоит обучение?

Helped me to change the break light on mine I couldn’t figure it out where is access to the bulb thanks

Do they both sand the same? Ive tried the fine but i want to order the coarse to try that because id like to start using these for dent work. The fine sands pretty hard so just curious if the coarse sands the same or not.

Kirlin Court

Very comprehensive demo on how the UV curing system works, for what I do a lamp like you have is just not worth the expense but what's useful for me is the UV putty as it cures very quickly even with my small lamp, I also have a rattle can of the Final Systems UV primer which is ideal for cut throughs after sanding plus I find the rattle can UV primer gives a good build👌 What I am interested in is those interface pads you use as they look really good for sanding primer to avoid those dreaded cut throughs, I remember you demoing them a long while back and I said then I liked them but I didn't get any but I think they would be very useful👍

Excellent repair.

Very interesting video thanks Wayne.

I'm trying to restore a PolyUrethane bumper, glass fibre reinforced i think, PUR-GF- 20 it says on the bumper. The thing is i have no cracks to repair but there is two "flaps" on the backside that is meant to hold the bumper onto the car with screws. One has partly started to get loose and the other one is completely gone. I have started to learn basic plastic welding and thought that i could fix this by welding the loose one with some reinforcements and make new one for the one that are missing. But i got very disappointed when i understood welding in PolyUrethane does not work, at least not with my simple tools. Is there any glue or other chemical method that bonds well with PU?

The only of repairing Vinyl is doing this.

I've got a early 1983 Audi Quattro that has a cracked airdam, looks to be polyurethane but the material is a black color, believe it's the same material as used in Porsche 944 fonrt air dam black color, need to know if I can use a repair glue or the technique you just used? I'm assuming polyurethane can be black color also?

I bought the walcom ego as i heard great things about it but sadly i just cant spray well with it no matter how i tried to set it up , might just be me but been sat in its box collecting dust i have a ani 150 that produces better results and my old sri lite

Music is overwhelming the voice. Can barely hear you.

Nice job as always Wayne, the Innotec looks like a good product as the result was a strong repair🙏☝

Would be good to compare it to the fast mover, proxl or upol 2k glue. This it £30 compared to 10 or 15

Very impressive repair.

Superb finish there Wayne, I can't remember seeing the Colad UV fine putty used over a large area like that before was that just to level it or to fill pin holes🤔 Maybe none of the above🤦‍♂

All I do is press the key pad twice and the rear door's open as well as the boot.

Loved watching this. Where do you get the Kovax equipment and consumables ? Thank you

Very nice job there Wayne and the instructions were very clear and easy to understand. I do like the Colad UV putty as it cures fast even with my little lamp it's only around 10 seconds but I do tend to apply thinner coats to build it up, I also like the Final Systems UV primer in the rattle can as I don't use it that much so it seems to keep better👌 Thanks as always for your videos👍

Beautiful job 👏

Can you wear glasses with this?

No commentary

Perfect. I just had the bottom lip pop out last night on the front door.

What prep station is that

Pryse to Suit AFRICA

Looks like an awesome peace off equipment

The TD3 just oozes quality and when you removed the filter the components under the red case look like a work of art, I really like seeing a quality product which isn't built down to a price👌👍

What pressure do you set it to on your gun regulator?

Got the same sort of damage on my BMWs door card, where abouts are you in uk? Want to get mine repaired.

On dirait mr macron

And an other cracking job done Wanye. Looks shiny 🤩

Another professional job Wayne the Finer Core is a great gun for base and clear, as you know Pete's Hobbies lent me his Finer Core and I've really enjoyed using it and used it for base the first time the other day it was just as good as my DV1, I'm considering getting one of these or the new 4600 but I can't decide which🙄😆 Thanks for sharing Wb👏👍

Helpful, thank you!

Great repair 👍 What is the plastic weld ur using ?

Nice! ABS, I assume?

Great video Wayne, lots of information. Thank you for sharing your work.

HI Wayne, great video and a good demo on repairing PUR which you said is a bit more difficult than other plastics, am I right in thinking that if you use the metal staples in a plastic you should remove them after the repair is done, as you demonstrated you can't use them with a PUR moulding🤔👍

This looks like a really good system ,I have the very good airless welder kit from Powertec but won’t to upgrade and there other kit are way to expensive ,can you tell where you got it from or did you import it

If ur going to use 2000 either way then you don't need to waste ur time and money on the tool...

I am loving your work! Do you know what Audi make their bumpers out of? I am looking to repair 2005 S4 B6 front bumper that has a crack around a fog light enclosure but not sure what filler material to use

Nice one good tip 👍

Please take this as a genuine question and not a dig. You’ve taken the handle and weather strip off but left the door moulding on.

A lot of this will come with experience and common sense but it's people like your good self that helps the novice get there a bit quicker, I've learnt so much from your videos. Thanks for sharing Wb👏👍