- 24
- 49 950
FalTac Garage
Приєднався 20 чер 2021
After Starting our Holster Channel (ua-cam.com/users/faltacunlimited) I decided to separate my passion for cars with my Holster business. Currently with 12 cars in my fleet, and most of them running. I wanted to allow you all to enjoy the journey of doing what i want with them. Id like your input, opinions, what you would do etc. From an all original 1970 Plymouth Cuda 440 to a custom hemi swap in my 91 stealth. this should be fun and i hope you come along for the ride!
How To Replacing The Spark Plugs In A 2017 Jeep Compass
Quick and simple video.
take the top cover off
remove each coil with one 10mm bolt
remove the spark plugs
replace plugs.
replace coils and bolt
replace engine cover
done
take the top cover off
remove each coil with one 10mm bolt
remove the spark plugs
replace plugs.
replace coils and bolt
replace engine cover
done
Переглядів: 228
Відео
How To Replace The Passenger Front Window Regulator In a 2018 Ram 1500 Quad Cab
Переглядів 1919 місяців тому
This was quite the process, definitely different from what im used too. The regulator is the ENTIRE plastic piece behind the door panel. And the panel mounts to the regulator itself along with all the electronics and cabling. so here was the step by step on what you get to look forward to and i hope this helps you save a couple bucks and do it yourself!
Replacing A Low Beam Bulb on a 2017 Jeep Compass, Passenger Side
Переглядів 1,4 тис.10 місяців тому
The easiest way i have found is a combination of above and below the headlight. so from the engine bay, remove the air cleaner top (3 bolts) and youll have some room to get in there and twist the cap off. Then from below, remove the 3 8mm bolts and the 1 10mm nut and fold over the inner wheel well and you now have access to the bottom and behind the headlight. rotate the headlight a 1/4 turn co...
Changing The front pads and rotors on a 2018 Ram
Переглядів 54Рік тому
This was going great, until the rotors were seized and the caliper was damaged by me taking it off. the rivet on the pad scrapped the cup on the caliper. Luckily my local store had one in stock and i swapped it out quickly. The rest is history!
I Installed better lights! So happy
Переглядів 392 роки тому
The days where I couldn't see a thing are over. the lighting was atrocious. these are 8 foot quad row 14.500 lumen lights and now have 8 hanging in half the garage. another 10 coming up and another 20 going on the second floor dor sure. here's a time laps of the set up. Music: Turn Up The Watts Musician: Jason Shaw URL: audionautix.com License: creativecommons.org/licenses/by/4.0/legalcode UA-c...
Sway Bar end links on a 01 Acura MDX
Переглядів 462 роки тому
Sway bar end links are pretty easy, but they can be stubborn for sure. Unscrewed one by hand and decided to cut the other off. But here's a how to on doing them, its pretty universal for most vehicles If you would like a holster, visit here👇👇👇 Faltacunlimitedllc.com If you'd like to email me, visit here 👇👇👇 Faltacunlimited@yahoo.com Follow FalTac Garage here👇👇👇 ua-cam.com/channels/DfWU2q-FKcjeA...
Jeep Compass Reset Oil Change Light
Переглядів 5462 роки тому
How to reset the oil life message. Step 1 press ignition button once Step 2 hit gas to floor and release 3 times Step 3 press ignition button once to shut off Step 4 start vehicle That's it! and your done!
How to Shut off the Maintenance Light on a 2001 Acura MDX
Переглядів 782 роки тому
exactly what the title says. how to shut off the maintenance light. step 1. insert key but do not turn step 2 press both select and reset buttons at the same time step 3. turn key to on step 4. wait 10 sec. light should turn off step 5. start vehicle
Changing spark plugs on a 2006 hemi charger
Переглядів 7802 роки тому
you will need extentions swivel 10mm 5/8 spark plug socket and time
How to Get your dull black trim back to a glass black using a torch.
Переглядів 212 роки тому
I show you a quick way to get your gray plastics that have been Sun bleached back to the pretty black they need to be.
How to replace the crank position sensor on a 2018 hemi Ram
Переглядів 1,8 тис.2 роки тому
How to replace the crank position sensor on a 2018 hemi Ram
Dodge Garage Application!
Переглядів 312 роки тому
Here it is folks my official #chiefdonutmakercontest video for youtube. Showing and telling a little back store on our all original 1970 Plymouth Cuda Build and tribute to my late father. Having a successful Holster Channel, this Garage channel was needed to separate play time from work time. FalTac Garage was born and for building s car like this and the story it has behind it, who wouldn't wa...
Rebuilding a 1970 Cuda Part 1, Steering Column
Переглядів 1362 роки тому
Rebuilding a 1970 Cuda Part 1, Steering Column
How to Change a daytime running light on a 2017 Jeep Compass
Переглядів 35 тис.2 роки тому
How to Change a daytime running light on a 2017 Jeep Compass
How to Reset the Oil Light on a 2018 Ram 5.7
Переглядів 493 роки тому
How to Reset the Oil Light on a 2018 Ram 5.7
Rebuilding a 1970 Plymouth Cuda Part 2, Heater Core
Переглядів 4673 роки тому
Rebuilding a 1970 Plymouth Cuda Part 2, Heater Core
I'm a "lotsa light" guy also. There is almost no such thing as to much light.
Where did you buy the park plugs
"Mo Bettah'
That was lit
Champion copper are the best
What about the whole replacement
Thank you so much for the amazing straightforward video it was very helpful, im going to be attempting this myself very soon. Ill leave another comment once im done detailing how it went. THANKS AGAIN
Straight to the point not alot of bs perfect video
Did you have to relearn the sensor
You just disconnect the battery when putting new one in and reconnect after clear code and turn off truck then restart it
After replacing, would I be able to take the truck to get code cleared? Or will it not be able to run if I don’t clear code right away.
Saved me so much time thank you
Why copper? , can you use Iranian spark plugs
car was sold the next day. didnt need to put more money into it than needed. just wanted it to be a good runner for the guy who bought it
Can the second method be used to change the low beam as well?? My driver side low beam is currently out and nobody wants to take my car apart 😫
low beams can be changed with the sae method for sure
how about telling us how to get the bulb out? does it have clips?
of course, there is a small tab that holds the prong
My top two bolts are flat caps and I can’t get them out! What the heck? I can see the light and everything just can get a grip to pinch and pull out the light. Any suggestions?
The bolt trick would of saved you hours messing with a stuck rotor…plus no chance of any damage…
Wow, super low miles.. will be watching, heater cores are a pain in the ass.
Love pre 72 Mopars myself. will be watching brother.
now that its finally nice in my garage im going to be doing more vids!
Thanks
Show everything except the important. How to get harness out and then back in. Great job 🙄
you dont know how to twist a bulb out of the suck and unclip it?
What i was wondering if it twists out, or just clips in.
Awesome thanks
I love short videos thanks for not fluffing this up !
How do you get the old bulb out?
Twist and pull the bulb from the socket
So that entire yellow piece, that holds the bulb, comes out and can be thrown away...right. I thought it was something that I needed to be careful with, but now I'm going to pry it out of there.
Sqeeze tabs and pull...no twisting involved.
Hey brother is part 1 of this video available
I believe it's on my other channel but I have to upload it to this one!
Man, you just saved me a lot of trouble!!!!! Thanks a lot!!!!
😔 𝖕𝖗𝖔𝖒𝖔𝖘𝖒
Quick and simple - thank you.
Thankyou, you made it very easy
Thanks for the vid! Whenever you get around to welding, Im sure you'll grab some Sheet Metal Clamps if you don't have, maybe consider practice laying dimes on some scrap 20ga. . Keep a couple few long shop towels and a bucket of water handy use the towels to keep both sides cool. Once you get front couple tacks you really gotta mind the buckling- Especially if the strip you're adding isn't Exactly the same Age and Thickness as the Base Metal since it's older . Maybe look for a few little baby spots on the body that can use a quick spot weld and tune the welder so it's laying a Flat Shiny Dime with a quick trigger pull and unless you're laying another dime immediately- Before the Dime and the Tip of the Wire cool from glowing- Make sure to clip the tip off the wire before another Dime to keep things clean an shiny. Alternate opposite sides laying baby dimes opposite sides of the strip you're adding. Only do a few, keeping towels close to welds to keep Heat Affected Zone close to the welds carefull nothing is glowing red but for an instant or it's too hot. Let her cool until water doesn't sizzle -don't let cool too much- make sure you've got good gas flow and you're good 👍Your gonna go through a ton of cutting disc's bro- you know you gotta where the respirator 😆
Man this helps so much!
Dual subscriber now bro... Nice ride - can't wait to see the progress on it.