- 52
- 48 105
Vu Ngoc Anh
Приєднався 12 лис 2012
Gold inlay on silver watch dial
Using my Andu engraver to cut an extra outlines and then remove backgrounds. After cutting the under edge and teeth with Andu Bulino pen - and then using the pen to hammer the gold foil into the surface. The Andu Bulino pen is very comfortable for the job like gold inlay, it will using for create the texture when finish the gold inlay surface too.
Переглядів: 195
Відео
Feedback from a customer from Bahrain and his engraved rings.
Переглядів 271Рік тому
This is the first time he using pneumatic engraver. The AnduHandControlled engraver is natural and comfort so the graver is like your longer finger - very easy to control even for new beginners.
Gold inlay with Andu Bulino pen.
Переглядів 8842 роки тому
Using my Andu Bulino pen for gold inlay. The pen shape give the easy ability to cutting precision tiny teeth for gold inlay. 90 degrees cross layer to lock the gold in place. And then change to carbide tip the Bulino pen is more than enough power need to hammer the gold melt into the surface.
Knife bolster engraving.
Переглядів 5812 роки тому
This is outlines for my folding knife. The bolsters is 420J stainless steel, the following step is gold inlay. I am using my Andu Handcontrol engraver and the graver is 3mm carbide 110 degrees. My email anduengraver@yahoo.com if you need more information.
Grinding 3mm flat graver.
Переглядів 6822 роки тому
Using my new mini power hone - it the upgrade version with new bldc motor. Running with slower speed but more powerful and almost no noise unless the cutting sound when graver put in. I hope you guys will like the clip and my new Mini power hone too.
Zippo lighter engraving.
Переглядів 3812 роки тому
The zippo lighter is engraving with our Ly Destiny's dragon. This is a gift for my friend. The dragon is present for Strength - Longlife - Noble in our culture. The engraver in clip is my Handcontrol engraver, the pressure setting about 0.3bar, the graver is 96degrees. I am thinking to add Abalone shell for the sphere and gold inlay for the dragon eye now. My email is anduengraver@yahoo.com is ...
Andu graver blanks and how to grinding 1.5mm carbide graver.
Переглядів 1,3 тис.3 роки тому
This is 3 kind of Andu graver blanks: 2.35mm squares, 3mm OD and 1.5mm OD with 3mm cover for tiny engraving It's very easy and quick to grinding index facet for next time re-sharpening round graver blanks.
SugarSkull 1
Переглядів 4333 роки тому
Engraving the skull for watch dial. I am making the only 20 watches on this SugarSkull series. The skull still need gold inlay and finish with miniature painting. The engraver in clip is Andu Handcontrol and 96degrees graver.
New test piece 2021.
Переглядів 3923 роки тому
Every engraver set come with the testpiece engraved by the engraver itself. Now I change to new testpiece to saving time for final testing. But the test could show 100% how the engraver performance.
Making the Hiphop trend watch
Переглядів 4063 роки тому
I made this watch to wearing at the tattoo event end of this month. This watch is really fun to making and I enjoy every moment of making it :D
Diamond Tiger watch dial.
Переглядів 3154 роки тому
The start of diamond tiger dial for my new watch. Stainless steel is quite strictly to cut, need raise the Face facet to 55degrees and 20degrees heel facets. But still need to cutting slow and light lines.
How to setup Andu engraver set
Переглядів 2,2 тис.4 роки тому
The air filter-regulator, pedal, engraver hand piece and few more item is come with the engraver set. It's just need few minutes to setup the engraver for running like this. I was preset all the air hoses size and noted the ports so you hard to get wrong, it's just simple plug and play. You could using white teflon tape for seal the air too.
Basic cutting lines for start practice engraving.
Переглядів 6 тис.4 роки тому
This is my foot control engraver. Using pressure is 0.6bar (8psi) and 116 degrees graver. The lines is about 3mm to 6mm long. I am not quite good on scroll work engraving and need more practice as you see but I hope this clip will give the idea for start engraving for newbie.
Easy gold leaf inlay on metal.
Переглядів 1,7 тис.4 роки тому
With my new Bulino pen gold inlay will be easy work - cutting hundred tiny teeth for gold, silver and copper inlay easy and fast. This clip is how I am inlay gold leaf on my watch dial - grinding the tweezers work as the bunisher at the same time make inlay faster. Heating the dial about 365-400°C at final step I will have patina color I want for the Phoenix and 100% bind the gold.
Phoenix watch dial of 2020
Переглядів 3814 роки тому
Start the 2020 with my Phoenix watch dial engraving. I love the Handcontrol engraver, no need to rust, just a littler and littler removing the background after the outlines..
How to change Andu engraver body tube.
Переглядів 1,6 тис.5 років тому
How to change Andu engraver body tube.
Testing the rebuild 2years old foot control engraver for my customer in France
Переглядів 3275 років тому
Testing the rebuild 2years old foot control engraver for my customer in France
Some step to do on my test piece come with each air engraver set
Переглядів 7385 років тому
Some step to do on my test piece come with each air engraver set
Some final cutting line on Maori watch dial
Переглядів 2325 років тому
Some final cutting line on Maori watch dial
Setup blank dial on Andu positioning pitch cup!
Переглядів 2485 років тому
Setup blank dial on Andu positioning pitch cup!
Nunome gold inlay technic using Andu engraver.
Переглядів 8855 років тому
Nunome gold inlay technic using Andu engraver.
Testing Andu foot control engraver fine shading line.
Переглядів 3655 років тому
Testing Andu foot control engraver fine shading line.
What is the piece called that you screw into the output of the regulator? The one that connects the foot pedal?
@mutchumbo Thank you for interested with my engraver. Please email me anduengraver@yahoo.com for catalog and more information.
What came out in the end?
@andrisgulbis9677 Thank you for interested, the dial still in making. I am not have time for engraving now, I will show clip when dial is finish and the complete watch too.
@@vungocanh5198thank you, please do something and take a vidro
I use air graver from Turkey and it looks similar to grs but for the dimension details I know for sure. can this be used on my collet
can this tool do some kind of dot engraving or some kind of scrimshaw on the horn. Because DOT and scrimshaw techniques require a soft touch? to make it look realistic. and I think it will require a small piston to achieve it
@mulanjamilah7849 Hi, yes my Bulino pen can doing Dot engraving no problem. I have a lot of feedback pictures about that. I have 1 2 customers is scrimshaw but feedback picture keep private. He tells the Bulino pen doing very good because you could lower the using press combine with stroke length adjust - but I think if you need really light dot maybe off the air and hand push is the best. The Bulino pen will help doing 80% 90% of dot work fast and effective.
@@vungocanh5198 thanks for your respon
why do i think of a billiard ball with my absence number at school the handle is 13😁😁😁scary number for someone but not for me. i am still alive😁😁😁
Where can I buy a handpiece from andu any contact information would be appreciated
Hi Raymond, Please email me Anduengraver@yahoo.com for catalog and more information.
Hey Brody you get my email?
Got your catalog if and when I order the foot controlled hand piece I'm gonna need a few of the bits the size your using to engrave the scull and rose motorcycle part .probably a 120 a back ground dimple bit a flat back ground remover trying to do car and motor cycle parts.not to much knife or rings or coin's Or jewelry!
Sounds like a 2-stroke engine.
Hello. Please tell me why your engraver needs an internal sleeve? Why can't you do without it? Does this engraver work better? I have never seen such a system anywhere. As far as I know, Lindsey does not use such a system either. Tell me, please, how much does your engraver cost?
Hi, that's my design not Lindsay engraver. Please email me anduengraver@yahoo.com for more information. Thank you.
what kind of graver did you use to do the inlay? do you use the Lindsay teaser template in the form of a rectangular box?
Where do I get one of those handpieces?
Please check, I just reply your email.
What brand of watch is this?
My friend using his name, he just make few watch a year. You could contact his Instagram - instagram.com/chienli.engraving?igshid=OGQ2MjdiOTE=
Mr. where can I purchase this engraver I am interested
Hi, please email me anduengraver@yahoo.com for catalog and details. Thanh you.
What watch is this?
Molto bene bravo continuate così grazie
How we can order
Hi Jora, please email me anduengraver@yahoo.com or ms me Anduengraver_maker in Instagram.
Nice
Not on Instagram anymore where are you now. I want to buy
Hi Troy! I am lost old Instagram account and have new one - Anduengraver_maker. Or you could email me anduengraver@yahoo.com my friend.
Well done my friend 🎉
Thank you my friend!
Awesome !!! 🙏😎👍🇨🇴
Thank you!
Nice work! Awesome hand control engraver!
Thank you Jim!
How do you keep the enamel dial from bending/warping? How does it stay flat after repeated firings?
Can you regulate the speed?
This is the old model, it's had the speed control but the new model is better control and more precise. Please looking the newest clip in my channel.
@@vungocanh5198 where are you selling them?
@@areyoutubed Please email me anduengraver@yahoo.com for receive catalog, I have more engraving tools too.
Beautiful work friend thanks
😂😂😂😂😂🤔🤔🤔🤔
Hope to see engraving on concave and convex.
Здравствуйте, сколько стоит шаблон для заточки с держателем и отправить в Россию можно?
hello Vu, I sent you an email
The tools froom hardisk?
No, hard disc motor is too weak.
Is there any way to order one of your handpieces anymore?
Hi, please email me anduengraver@yahoo.com for more information and catalog. Thank you!
Sir where r u buy this power hone
Where r u buy this templates
I am making templates myself.
I'm still waiting on communication to buy mine. He just disappears... :/
Hi, please email me Anduengraver@yahoo.com. Please tell me your email so I could search our old conversation. I was reply all messages and emails.
Hi, where can I contact you?
anh cho em hỏi mấy cái mũi sủi này a mua ở đâu ạ? Và anh có bán mũi không ạ? A có zalo không ạ cho em xin em muốn trao đổi 1 chút thông tin với a ạ!
Mũi a tự mài từ HSS hoặc carbide tùy theo nhu cầu. A sx và bán tool chạm khắc các loại nhé. E add 0975873689 nhé.
@@vungocanh5198 over stainless steel?
@@giwangpvcartslamp1349 This is blue steel - same hardness with stainless steel. But the stainless steel is strictly material to engraving is not by hardness - it's because the chips hard to breaking. You need raise graver angles and cutting bit by bit with stainless steel is ok.
@@vungocanh5198 I like your videos but you rarely make videos. I want to see the latest development of your handle. You know I still want your tools but there's something I can't say here. about your carving tool
Great work mate 😁👍
Thank you Ryan!
Chia cho e bộ mày mũi a ơi
Hey mate do you sell graver sharpening templates ??
Adjusted idle on my graver but it doesn’t stay at idle. If the hand piece moves slightly it stops idling and majority of the time when I activate Palm control it just hisses air. I have to a hard rapid squeeze to engage movement, by this time I can’t actually start off slow and steady.
Hi, it's sound like you setting idling too fine so engraver easy to stop and not keep idling. You could setting idling high now - but not give cutting power until you push the valve for control. And make sure the engraver is clean - I have clip how to cleaning engraver here too. Handcontrol engraver from 1:55' I was tested every engraver before send to make sure they are all good condition when left.
mũi sủi này a mua đâu vậy anh? Hay a có bán k ạ?
Let us know when these are for sale
Hi! Thank you for great video! Is it acrylic paint? Do you use some varnish on top?
This is enamel - basically is glass powder. After painting I will using kiln with about 800°C for melting and bond.
I lost track of you on Facebook messenger. I was going to order but you didn’t have engravers built at that time. So I am just checking back with you to see if you have any assembled now to sell or will soon. Thanks
Hi Micheal! Please email me anduengraver@yahoo.com for catalog and more info.
Awesome work I barely started to practice engraving with a home made engraver I made what kind of engraving machine are you using
I am using my Handcontrol engraver for watch dial.
Beautiful work Vu!
Thank you Jim!
How do I purchase? Please contact me 👍
Hi Chris! Please email me anduengraver@yahoo.com for details.
Can I order a watch case from you to fit a ETA or Unitas movement?
Thank you Isaac! But I am just making piece by piece now to fix my spec of dial thick. It's may not fix as a glove with ETA dial and high standard.
Thank you for the instructions. Your engraver is very, very good.
I want to know where I can purchase your equipment?? I am unable to find a website for you. Please contact me.
How and where do I buy this set up? And engraver? Thanks
I love my engraver I bought from you!
Does it has hand control for speed?