![Abdel-Rahman Hussein](/img/default-banner.jpg)
- 6
- 72 698
Abdel-Rahman Hussein
Приєднався 8 чер 2016
Mechanical Power Engineering
Architecture | Revit Tutorial : How to design a Spiral Staircase.
Facebook Studio page : abdelrahman.reda0535/
Revit
how to use revit
revit architecture building
information modeling
autodesk tutorial
revit tutorials
spiral staircase
Spiral stair
autodesk
revit architecture documentary architecture
lecture for beginners
architecture student
Architecture
architecture lecture for beginners
autodesk revit
building information modeling
Revit
how to use revit
revit architecture building
information modeling
autodesk tutorial
revit tutorials
spiral staircase
Spiral stair
autodesk
revit architecture documentary architecture
lecture for beginners
architecture student
Architecture
architecture lecture for beginners
autodesk revit
building information modeling
Переглядів: 15 383
Відео
Solidworks Tutorial | How to design turbine of a Gas Turbine.
Переглядів 8 тис.2 роки тому
This is a tutorial about how to design the turbine of a gas turbine using solidworks . Dimensions of blades and rotor are to be determined based on specific calculations. Gas Turbine Axial Turbine Solidworks tutorial HP Turbine Solidworks Simulation Learn solidworks Solidworks lessons High pressure turbine Jet Engine Power plant solidworks tutorialsolidworks tutorialsmechanical engineeringlearn...
Solidworks Supersonic Projectile Aerodynamic Analysis
Переглядів 2,7 тис.2 роки тому
Solidworks Supersonic Projectile Aerodynamic Analysis
Solidworks tutorial | Sniper cartridge-bullet + Simulation تصميم الرصاصه سوليدووركس
Переглядів 3,1 тис.2 роки тому
Here is a short video about making sniper cartridge on solidworks and make Air Flow simulation for it , it's a simple design of the body and how Air flow over it . Dimensions are different from one cartridge to another based on density of air , temperature, range &destructive power needed. فيديو قصير لتوضيح كيفية تصميم الرصاصه في برنامج سوليد ووركس وعمل محاكاه لحركتها وسط تيارات الهواء, تختلف ا...
Solidworks Tutorial l Make Marine Propeller for ships & boats + Water Flow Simulation
Переглядів 37 тис.2 роки тому
It's a short video explaining how to make a 5-blade Ship Marine Propeller on solidworks , and water flow simulation for it. Note that the dimensions are to be determined depending on size of ship "load" , maximum rotation speed and the thrust needed. For more details you can back to Turbmachinery study , Mechanical Engineering. solidworks tutorial solidworks tutorial for beginners solidworks tu...
Solidworks Tutorial | Centrifugal compressor | Rolls-Royce Jet Engine.
Переглядів 7 тис.2 роки тому
Here a short video about how to make a centrifugal impeller on solidworks , The dimensions are determined on specific calculations based on flow rate and pressure out of air required . For more you can back to TurboMachachinery study . Source : Rolls-Royce The Jet Engine. "Book" #RollsRoyse #Solidworks #Solidworks_Tutorial #Compressor #JetEngine #TurboMachinery #MechanicalEngineering #Engineeri...
Could you please provide which research paper did you use ???
Can you design a racing propeller that has a sharp point on the end of it (chopper prop)?
the Cartridge doesnt fly.
Great thanks
Great Tutorial but why the rush?
I dont know why but in mine water is only entering from back side of propeller when rotated in both directions
If i forgot to set reference axis how can i edit ?
Way too fast! It was very hard to keep up. I had to keep rewinding and pausing.
جهد مشكور على هذا النوع من السلالم الصعبة الرسم وهذا النوع من السلالم مشروح طريقة رسمه بالتفصيل خطوة بعد خطوة في كتاب Revit 2020 for Architecure
Hello, i am making a simple animation of boat. With the purpose that this animation can give me best shape of a lower part of a boat in water and that boat has good aerodinamic. So i can make it in real life. Do you have any recomendation about how do i get to this shape without using programming. I am on a schedule, so i would be very happy for answers. Thank you very much!
Batane hi hai to samjha samja ke bol bol kr bataiye
The velocity you showed is of the fluid or propeller?
Tutorial not fast enough
agree. try using 2x speed
It's too fast 😢
can you make a tutorial on simulation for a bullet traveling down a barrel ?
You deserve subscribe brother 😊
thx!
Can l get the Cad?
روعه ي هندسه
جميل ممكن flow simulation
الله يوفقك ويحسن مابين إيديك دايما يارب💖💖💖💖
بالتوفيق دايما وربنا يحسن مابين إيديك يا بشمهندس💖💖
عالمى ❤
❤❤
ما شاء الله بارك الله فيك
ماخلاص يا جوجو
شغل عالي
اخويا
عالمي
nice
Thanks
😍😍😍😍
nice one
Thanks
gjffg
Nice
Thanks
NEW
AMAZING
Thanks
hkfdg
Good
Dikjctn bjj
Well that's amazing
Thanks
Nice
cool
Djsb
Nice
ua-cam.com/video/b0K7ca9gOKY/v-deo.html
Super
Thanks
👍👍👍
❤️❤️❤️❤️
wer tyui nb
ua-cam.com/video/8yJEAWY7jE0/v-deo.html
Amazing
Thanks
nice
nkgjhgb