Відео

Hey like a great build! Excellent! TYFP!

You are a genius! Thank you!

This is so ingenious! Thank you for posting this. 😊

how can i oder address please

How’d you get the rope up the tree initially

Thx for sharing

no reference to RAM ? What kind of memory did you put ?

Using this methodology I built a 148’ end fed long wire dipole elevated from 30’ to 70’. This technique allows one to raise and lower the antenna from both ends allowing examination, repair, tuning, experimentation etc. After installing an in line grounded coax lightening arrestor from the 9:1 unun I was pleased that my SWR had not changed. I hoisted both ends of my dipole and was back up and running. This build finally complete.

TImes recommends only crimping at the top. ua-cam.com/video/UKmCObs2ojw/v-deo.html&ab_channel=TimesMicrowaveSystems

Cheers bud!

Great tutorial. It’s a shame there aren’t more on your channel!

Ok so I watched the entire video and did I have wiring already in place this doesn't help me much. Can you make a video for the next steps on how to create a windows based NVR , hopefully not with BlueIris but maybe frigate or other software and the associated setup. Or maybe link me to an existing video. Thank you! And keep up your great creative videos.

Love your videos. Thank you for this one. No one explains these PoE cams and I love them. Looking to replace my current PoE FLIR cameras and NVR with something more modern, with good app and without subscription. I have poe camera, 8 port poe switch and all wires through my attic already in place from the old FLIR system. Watching your video now.

Great video, this was the first video I watched on SCAD and I followed along and understood everything. Great attention to detail and very informative.

I bought the Arrow pneumatic stapler as well after using a Ryobi battery powered one and a manual stapler that just couldn't do the job nicely. It works great! Plus it has that nose on it that allows you to staple into tight spots, which I needed for the ATV seat cover I was replacing.

Has anyone had issues with network speeds slowing with this setup? I just recently bought an HDHomeRun and set it up with plex. Easy set up and works great but I usually get down speeds of over 900mbps and with HDHomeRun connected I get like 80-90mbps. Then back to normal if I disconnect it.

The other version of the board is a copy of the Alctron MA-1 circuit. That has the ability to short out pins 2 and 3 on the input to disable the microphone but the MA-1 case did not bother to put a switch on the outside. As CL-1 eventually also decided not to add the disable switch,so the final board does not have the jumpers.

U did a great job for a nubbi.

There are several cable cutters listed on the same page...2 orange handle ones. Could you give me the item number and price. Thanks.

Does the Plex server need to be near the tuner/antenna? Asking as I have my server in the basement but want to put my antenna near the roof, and have the tuner somewhat close as well

Lo caros que son y solo trean Dos Chips🙄

Nice job. Tried it for raising a bird feeder out of reach from deer. Worked like a charm!

I am new to SCAD but it appears to be a terrific tool to make useful parts. Excellent content. For us old folks it moved very fast. Will watch it again.

Hello. Very nice work. I want to now if you have an image of your raspbian with the onscreen keyboard or if no can you explain howto install it in Raspbian ? Thank's.

Went looking for a tear down for the CL-1 and stumbled on this video which is so well made and explained. Amazing work!

This is an excellent design and method for suspending an antenna from the tree canopy. I have been looking for a quick way to test different antenna builds for some time, so I was impressed when the UA-cam algorithm recommended your video. This retractable pulley system now allows me to rapidly prototype while ensuring better compliance with homeowners' association regulations. Thank you for sharing your design and technique.

Thank you for showing that removing the transaxle and cleaning the magnets & filters is the correct method and no modifications are necessary.

What about adding and external pump and hose barbs and plumbing in an oil cooler and possibly filter to suck out hot fluid and pump in cool fluid?

I appreciate this. We have the same set at my job but no one knows how to use it. Took the initiative to learn

Thanks so much for this. I used this today to put an efhw antenna in a tree in my backyard

This box has a lot of potential, but I’ve had numerous problems with this. First is getting ghosted by customer support. Secondly, the audio for the Nextgen channels does not work unless you have a Roku Ultra. Do not buy the Ultra LTE version from Walmart; it will not work. Will also not work with lesser Roku models. Also, the channels that are encrypted are not supported on the HD home run. This is a complete opposite of the Zapperbox. One more thing - the internet connection it needs isn’t wireless. The one benefit this has over the Zapperbox that you have one tuner and one antenna that you can place anywhere and have over the air television on every TV in your house that has a Roku or a Firestick. I keep mine behind the bed in the upper floor bedroom with an amplified Channel Master flat panel antenna in the window facing most of the towers.

I need to do this!

Is there a way to integrate UA-cam TV into PLEX?

so it just barely works which is not good.

Nice video but I like soldering my connectors. Have it down to a science. To me it’s an art. I take my time and enjoy it. The end result is beautiful.

These should be standard on every printer, imho. Integrated PID control, etc. It only needs a little air flow to move away the evaporated moisture. The new models have a air pump. I modified mine with a small fan..stays blue even in the humid months.😊

Thordson works.

nice

I have the same conduit in my house. I am so happy the builder in 1996 thought of this. I plan on just buying an antenna to put in the attic. The conduit comes down close to where our coax setup (that we only use for one cable router).

1- can you re-use those type of connectors?

This is a really cool project specially the box for components! Could you please share the link for it?

Is there a way to remove the default Plex live tv streams? Or do you think they are a value-add and I should keep them in if I’m setting this up for an older family member?

Some points: (1) HDHomerun Flex 4K doesn't pick up encrypted ATSC 3.0 channels. (2) Don't bother connecting this tuner to Plex or Emby as neither support Dolby AC4. So, if you are able to watch the video stream on ATSC 3.0 non-encrypted channels you won't hear anything. (3) The HDHomerun app works ok on the iPhone. Unfortunately, there was no HDHomerun app for my Samsung TV. (4) Some of the audio streams for ATSC 1.0 channels sound terrible. As if the sound is coming from a tin can. If your goal is to stream ATSC 1.0 content throughout your house using a Plex or Emby server and you don't care about NextGenTV then this is a good product. However, if you want to experience NextGenTV then something like the Zapperbox would be a better choice. Keep in mind that ATSC 3.0 is a mess. There are currently no 4K channels. The broadcasters want to encrypt the channels and they want everyone to get internet access when watching broadcast tv to get the encryption keys over the internet.

Can it be used for construction purpose?

Nice idea but not ready for prime time.

Brilliant video. Extremely followable and reproducible. Well done 👏🙏

Was looking at amazon reviews saying, "It beeps way too early!" and person saying about "85 percent before its actually there" Well people, its gradual, thats what you should want! Thank you for making this video. Sealed the deal.

Hello, since LSK389 is unavailable where I live, is Toshiba 2SK389 a 1:1 (as of specs)/ good replacement?

Woow, didn't know that was possible. I was just looking for info on openSCAD. Would definitely now learn it :D Thanks

How many hours did you do in that one year, thanks