- 11
- 435 599
joger 77
Poland
Приєднався 14 лис 2013
Відео
Steel sleeve - silent tool boring bar
Переглядів 21 тис.3 роки тому
Steel sleeve - silent tool boring bar
Boring bar - Silent Tools from Sandvik in use / Bronze bushing.
Переглядів 9 тис.3 роки тому
Boring bar - Silent Tools from Sandvik in use / Bronze bushing.
What Ap?!
Likes the camera angels.
Ок
That's a darned long boring bar! The quality of the surface is amazing, especially considering the length of the bar. It would have been interesting to check the cylindricity.
2 principi...no uno..cazzone
What brand tool is it?
Sandvik Coromant Silent Tools boring bar.
silent ??????????????????????????
Yes, absolutely. That tool is out someting like 10 to 13 times diameter. And in that kind of condition that was an amazing job, that you couldn't do otherwise... and since vobration is an high frequency resonance, and there is no (or at least very very low) vibration here... it's truly silent.
Nice job!!!
Half the job is picking the right tool. And here is the right one picked. :-)
👍
One done, 4,999 to go..lol
Good job......👍👍
Matou a bucha! Canal não deveria sair para além do canal de lubrificação
指令碼是G32嗎?
yes, that's g32 code
That was a clean cut, I liked it 👍
Bonjour
反螺旋油槽 很棒👍👍👍
对铜件也有抗震效果吗?😄😄
Ordinary tools also work easily on brass in any situation
At 10xD while maintaining realistic parameters? Ok 👌
Tak można pracować 🤣👍
It's wrong I know perfect work lining only inside
Co to za producent i model maszyny?
Pewnie Polski TUR
Pracuje na takiej samej maszynie💪, pozdrawiam
Very nice, I love a boring video lol!
Stuck out!
Nice holder
Right tool.left threading,
What's the useing ? Plz explain ?
It’s a lathe
@@porkerthepig i<3u
It's going dry, hear her whine on the pull out?
Facing left use the best, try...
Huh?
Machined on a Colchester 3000L ?
Sbagliato..non si fa una vite a un principio ma a 2..così non serve a un cazz
You could give the whole production and it would be better. But it's still a nice video!
Definitely can not complain about the finish. I have heard that these bars only work IF you push them hard enough to make them work ?? Seems like what i heard is BULLSHIT. Seems like a fairly light cutting depth from what i could see. Maybe i should buy myself one of these bars for my next Christmas gift. I doubt no matter how Good i am. Santa definitely will not be bringing me one, LOL.
You are right about the BS. They work at any cutting depth! And as for everything, you can manage to use them so you do not get the best out of them. But even then they are better then anything else. Hope Santa one day change his mind, as we have plenty in stock :-)
Reminds me of a very similar part i machined on my Manual Lathe, except the thread pitch was around 2 tpi, Fun Job ????
ด้ามละเป็นแสน
It's pretty cool, such a tool pole about how much.
Holy macaroni
feed/speed/material? ive tried this insert on a few different materials and had the best luck in 4340. still more productive to just grab a 643cnmg and take .35 a side in my opinion
Это правда🙊
Amazing, any other changes done in machine .. i mean ... eg: tool clamping
厉害了
Poderia me dizer o diametro desta barra, o comprimento utilizado, o material da peça e o valor médio da rugosidade ( Ra) depois de usinado?
realmente uma ferramenta excelente, qual o preço de uma barra dessas ?