Відео

the on and off switch on the right hand side is on off is all the way down

@rydenloopz good one! I figured that much out, even on it only works when i plug it up

Just assembled my daughter's last night just tried to start it can't find the damn fuel valve lever it's just not there

@@ianmcmaster7531there is no fuel lever put it on choke when you start it then after it's on switch it to run want me to make a video?😊

Hello, what is the SKU for this item you purchased? If it is the 75025 pump that is in the video, unfortunately a warranty is not offered. We do have parts available at xtremepowerusa.com

Hello, unfortunately we do not have a reseller in South Africa.

Hello, these bikes are still available for purchase on our website ihubdeal.com

Hello, there's a drain plug at the bottom of the engine, loosen the screw to let the oil drain.

Replacing the puller starter is very easy, use a screwdriver to loosen the screw then put a new on.

Please click the link for this item in the video description for pricing and availability.

Hello!

Hello, any 4-stroke oil will work for these models.

Hello, 55℉ is the minimum temperature.

Hello, due to stability concerns, this machine is designed to be used on a flat surface.

It might be a faulty o-ring, or some of the connections not tightened enough. Please refer to the troubleshooting portion of the user manual. It can be found here, just toggle to the bottom of the page. ihubdeal.com/products/2640-gph-self-priming-swimming-pool-pump-w-timer-13-sand-filter-above-ground?_pos=1&_psq=75159&_ss=e&_v=1.0

yes, we are located in California. Please visit us at ihubdeal.com

Hello you can purchase an o-ring for this item at xtremepowerusa.com

Hello, you can find the Hi/Low switch on the back panel of the pump.

Hello, it is located on the back panel of the pump.

Hello, No this pump is heating mode only.

Hello, parts for this item can be purchased from xtremepowerusa.com

Hello, have you received a response from our customer service yet? If not, please provide your order number and I will look into it.

Φ145.42*Φ6.99 mm

I also had this problem. Did you find out a way to solve the problem?

@@gaelgarcia161no, not particularly. We replaced the sand with filter balls, but unfortunately our pool is still has sand on the bottom of it.

What type of pool sand must I use

@@jimjigga I am not sure what to recommend, like my comment above said sand didn’t work for me

@@zachbumbarger4297 how can sand not work in a sand filter pump?

How is that I'm recently doing my research. Where would I get them .

Online

1 box of Filtra Balls weighs less than 2 lbs and is equivalent to 50 pounds of normal filter sand.

The video does show that the ground wire is simply capped (the yellow object). I did not see that any other wire is connected to the ground wire. My old system had the green screw for grounding. I plan to call the manufacturer and ask if I don't see any response here.

@@Choam666 If you learn anything please let me know.

Did anyone find out where to connect the ground wire ??

I have installed these before but not this updated model And it was already wired when I got it So not sure on this one It’s 240 v Let me know

Hello, the green cable should connect to the metal screw which is on the bottom, then connect the green cable to the nut, the nut near the bottom.

Hello, to turn it on you have to turn the dial to "backwash"

3/4 full

To turn the pump on you turn it to BACKWASH. The amount of sand to use is 42lbs

You do it manually

I have the same one ain’t no power button

⁠use a timer

@@Tungoon To turn the pump on you turn it to BACKWASH.

1.25 in and 1.5 in

Hello, 2,853 GPM on low speed.

@@ihubdeal4918 thank you!

Hello, please ensure all suction and discharge valves are open when the pump is running. It could be one of the following reasons. 1. The strainer is clogged. 2. The pump location is too high, or too far from the pool. 3. Undersized pool piping. 4. A valve might be partially closed or blocked. Please refer to Troubleshooting section in the manual for more information.

On the filter barrel, there are two waistlines. we recommend filling the sand up to the top waistline, and for this model, it will take around 30 lbs of sand.

​@@ihubdeal4918 What kind of sand?

@@JP-ku3he Silica pool filter sand is the most commonly used type

2 5/8

Hello, It might not time to backwash yet, if the water still clean. You should backwash a sand filter when the pressure gauge on the filter reads 8-10 pounds per square inch (PSI) higher than its starting pressure. You can also backwash when the needle on the pressure gauge is close to or within the red zone.

I was told that the cotton balls are better. As of now, I am using sand but will switch to cotton balls.

Hello, sand is preferable for this item. You can find the manual here, just toggle to the bottom of the page: ihubdeal.com/products/2640-gph-self-priming-swimming-pool-pump-w-timer-13-sand-filter-above-ground?_pos=1&_psq=75159&_ss=e&_v=1.0

No, they are correct.