Відео

No 1❤

Beautiful work!!

Very nicely done all you now have to do is learn to talk.😊😊

Have you tested it? No weld i've see

Nice build, I am currently building one, different design. Did you have to isolate motor from unit for welding?

This is extremely helpful for potential buyers. Garmin should def pay you and use this in their promo videos. I'm getting another one as a rear dash cam. Thanks much!!

عمل رائع ❤ ، اعلم انه يمكنك ربط المحورين في الاعلى ببعضهما البعض عبر المسننات ، ليتم الرفع والنزول بنفس الدرجة بالضبض، لكي تحصل على سهولة في المعايرة والعمل . اقدر جهدك واظنك قادر على تطويرها .❤ تحياتي لك من فلسطين 🇵🇸😊⚘️

Have you run this with AC high freq. TIG? I have the same motor and control and the HF makes it go full speed only.

This is really well built. i just use a piece of flatbar with a bolt for a handle and drill a hole at the diameter I want that fits the torch nozzle tightly then jam it in there lmao.

Honestly don’t think the lapping wheel is rated for that speed.

A well thought out and executed project. Nicely finished.

Pretty cool tool, Tom.

Great design! I enjoyed watching

Which specific quick change tool did you purchase? I’m looking on their website and it has three or four different styles. I am new to this lathe as I just purchased it and would like to put a quick change on it

Looks realy good like for me! Good video quality. Good price. Works well in all light conditions. Thank you for test! I will buy this camera now after your video! 👍👍

Hell yeah. I need 2 of these. Ha

Why didn’t you go with the hammered blue like everyone else does

Great work! Meets all the needs in one package. What does the braided ground strap tie into? Is it just grounded to the body of the machine? Or is it tied into the controller board?

красавчег сделал охуенно . респект и уважуха. я буду делать примерно как у тебя но с возможными вариациями как сделаю то обязательно тебе сообщю.😊

Thank you very much.

Thanks for this video, I was wondering how I was going to adapt my new tool post to fit my old lathe. Blessings to you!

Love to play with that for awhile. I spent a life time running both engine and turret lathes. You don't do that if you don't enjoy it. My one regret of old age. I didn't have some small machines and a place to use them.

Another mutetuber. Great. /s

Im makeing one myself..and its not complicated at all...

Good work! Have you considered a latching switch for the foot controller.

I think this dude likes springs

Genius

Best one I've seen yet, only thing I hate drilling holes in the piece I want, so magnetic is the way to go, seen some with a bearing in the torch head, but wonder how they hold the torch head in it, probably just a loose fit like yours. Have to get the lathe and mill fired up. Thanks for a great video and all your work of putting it together. 👍👍👍👍

Yes please sell these!!!

Very nicely done!!😊

Nice job, Maybe a smaller magnet?

Thank you. Going to get one tonght after 2 accidents that were not my fault but ended up 50/50.

pls sell these ....

Bravo vous êtes un grand monsieur ❤❤❤❤❤

You don’t have a full range of turning the way you did it. You have to mill the cross slide back a little so the square tool post will turn 180. I an add photos if you would like.

Dude is that 4sale

😊

Dagur Barkarson asked why does the footswitch take over when it's plugged in. The phone jack I used is similar to a microphone jack or a jack on the input of a guitar amp, where when you unplug the plug, a little switch contact in the jack grounds the hot lead of the jack to ground. If you buy a phone jack from a place that sells them for electric guitars, or to repair guitar amps, that's most likely the type you'll get. They do that so when you yank the cord out of a guitar amp, there won't be any hum from having an "open" connection. Within the motor speed controller there is a relay that turns the power on and off and controls the direction depending on which wire you connect to ground. The center (common) lead of the toggle switch needs to go to ground for the directional switch to work. I took that lead that came from the center common terminal of that switch and ran it to the hot terminal of the phone jack. When there is nothing plugged into that phone jack, that lead gets grounded by little switch contacts in the jack, so you can turn the motor on and off on the box. But when the phone plug is plugged into that jack, it opens up the "hot" contact that would be going to ground, and connects it to the foot switch. When you step on the footswitch, it connects it to ground. The pin at the tip of the plug is the "hot" side of the plug, and the barrel of the plug is what connects to ground. Hope that helps you out.

great work! can you tell me, why does the footswitch take over after its been plugged in ? i dont understand how its wired to be able to run without the switch.

The places where it skipped, we call those safeties keeps the part from falling on your toes and keeps you from feeling bad about the inconsistent travel speed. great job on the guide.

Hello, I wanted to ask where you took the engine from?? What is the name of the engine, how powerful is it, and where can I get one? Can you maybe give me the link to buy such a motor?

Hello, I wanted to ask where you took the engine from?? What is the name of the engine, how powerful is it, and where can I get one? Can you maybe give me the link to buy such a motor?

Hello, I wanted to ask where you took the engine from?? What is the name of the engine, how powerful is it, and where can I get one? Can you maybe give me the link to buy such a motor?

Very nice pasta roller.

Hello I would like to ask what motor you use can you maybe give me a link for purchase.

Good afternoon. What motor did you use?

Thanks for the examples!

That's bad ass my bro.

This seems unnecessary to people who've never dealt with racoons, skunks and rats. Always over engineer when dealing with pest control. I replaced all vents, and the vermin made holes around the outside of those screens. Currently replacing everything. Vermin (rats, racoons, skunks) will chew through concrete and wood. They will physically pull the shingles off your roof near attic vents. I had no idea they would manage to tear up a wire screen! They are relentless, and take days to make the access hole. I'm going to look into your method of attaching to concrete. Any exposed wood near vents, not covered by metal WILL eventually be compromised. If you live near a storm drain, and have heavy rainfall, your home foundation vents are going to constantly be visited by rats escaping the high waters within the storm drain system.

You are abusing this small grinder, rather use a powerful 700w grinder