Відео

How to change a bad wheel lugg?

Great video

With so much grease on the inside aren't you concerned about grease getting on the brake shoes?

Very informativan clear, the best video yet, I really appreciate this!!!

How do you run to carb lines and what lines do you use

When these go bad does it mean the parking brake no longer works?

Very, very smart young man. Nice tutorial

Valeu Fron brasil thanks 🙏

I hope folks dont follow this repair... a little grease goes a long way

Guess you dont understand dry torque versus wet torque 😂

A hundred is a hundred…not 80…ur 20% under…😳

Four years later How are things going? I just became a ham and working on getting my antenna up and going. Congrats of your first call. Michael ~ KL5NU

"You've got 20 minutes to use an entire tub of grease...go!!" "I have just the project for that! Rear brakes!!"

that was one of the best vids I have seen on UA-cam. Damn fine job.

It’s fools errand if you ride hard trails. I’ve sealed the drum housing with RTV and still within half a day riding the drum is pooched again. It’s too bad there isn’t a hydraulic disc brake conversion for around $300. The mechanical cable disc conversion is just slightly less useless than the drum, but a hydraulic kit could be the ticket - even if only operable by hand lever and you lose the foot brake pedal

You shouldn’t be working on your own stuff

Holy grease, Batman

nice good job boys thank you

Thank you guys!!!!

Best video I have seen . Think you.

Good job!

Using that much grease on the axle splines will have you without brakes again in no time. As soon as the shoes and drum get hot it's going to be all over them. A light coat is all that is needed.

Good job. Informative. Bare footed... no less

To much grease. Any grease left beyond the point where you need a lubricant, will attract dust and can cause that dust/sand to migrate onto the face of seals or bearings. Just a very thin layer will work just fine. Just saying.

Bro I would love to do what you do but I can’t

2wd or 4wd

I love Honda. They are dead nuts reliable, mostly due to their simplicity. That being said, their drum brakes. Wow. What a hassle. I don't think I have ever purchased a used Honda ATV where the drum brakes worked even a little. If you ride in areas with a lot of mud/water, you need to either do a disc brake conversion or learn to ride without brakes and just using gearing. Working on a 2003 450 S that I just bought. Rear shows no signs of life. Up front, all 4 wheel cylinders were frozen solid. I have the front brakes functioning now (waiting on new shoes). On to the rear I guess. Thanks for the video!

No helmet?

So i got mine snorkeled with the intake and 2 diff lines but it keeps cutting off, I dielectric grease on my spark plug boot and siliconed it but it still keeps cutting off. What vents did you run on the carb??

What did u use to clean it

How many vent lines do you have

Hardest part of it all is finding that 10mm socket

good vid but.... you start off stating that your dust cover seal is shot and I was expecting you would show the install of a new seal.

come back bru

Why do you go so fast

Guy doesn't know how use a torque wrench.

How many 90’s or 45’s

10ft? Pvc

I can't get the damned drum off, somethings seized good .....

I’m about to put rancher stocks on mine to

I cannot for the life of me getting the axel hub nut off. I've hit it with wd40 and penetrating oil, even tried applying heat for a little bit. I currently have both back wheels off and have a crowbar bracing the other side so the shaft cannot turn. Rather sure the breaks are seized up as I cannot rotate the shaft by hand. Either that or the bearings have seized? I can't tell until I can get that hub nut off. Any suggestions?

What about the gas vent line

great video, well though out...however I will add the shaft that controls the shoe movement will and can get stiff almost seizing up if not cleaned and lubricated, Ive ran into this on several machines. if it does not move freely, the control arm will have to be removed and the shaft knocked out, cleaned up and greased before the brakes are installed

I just dont understand why super atv or highlifter have not made a conversion for the 2014-2019 foremans and ranchers yet. There is a massive market for them but they are just dragging ass on it.

They are still gonna go rite out, the only way to fix that is to actually drill large holes on the bottom of the drum cover so it doesn’t hold sand and water in the brakes

Make a video vent lines for the carb

Where exactly its the enter do you have to pay to get in ?

Are they still working?

How much did that cost?

Nice video