Відео

Thank you mate, I was looking for something like it, seems like the best DIY idea for this job.

You're a good dad, but dang those lazy kids haha. I'm thinking of doing this too.

I'm a firm believer in plugs over patches, been using them since the mid 70s they have plugged many of holes in many places on the tire, one time working in the shop a car came in, to my Suprise with a plug right in the side wall about mid-way, holding air not leaking one bit, ask the customer if he wanted a new tire he declined, and after the service drove on his marry way. I do know patches don't work very well most don't stay and fall off the inside, many cars came in after patches applied directions followed leaking like a sieve, they don't galvanize since they quit lighting them, you can have my plug kit when you pry it from my cold dead hands plugs work

Great videos, good explanations, tips and tricks included. ✅. Where did you get the valve gasket kit? Brand? link please. On the water pump, where did you purchase this motor longer bolts? Thank you for ALL your videos, watching from North Texas 👍🏻

So if the 2000 Celica GT has over 386,000 miles would one still use the existing springs or go with new ones? Yes folks it has 386,000+ miles, is on its second engine and already have a JDM long block in my garage on a pallet 👍🏻.

Thank you. I love diy. Hate going to AutoZone. My neighbor has tons of angle iron laying around. Saved another buck!

Great idea. I usually compost my leaves over winter and early spring. Makes for great soil for the garden

👋😲何してるんだい？

I was away taking care of my mom for six months and came home to wax moths …thanks

I watched 15 videos and this is the only guy who actually fixed the problem 🎉🎉🎉🎉🎉❤

I have the same model of car and recently the cllyinder 4 have a misfire , did spark plugs / ignition coils/ and all new fuel injectors , it’s visibly misfiring when I run the car , could it be a bad piston ring or would it be a similiar issue with bad valve cover seal ?

Thank you for showing us how to do it on the shoulder/sidewall, you have rescued countless of us from being taken by the crooked mechanics who just wanna make a sale.

Hey Tone Dubb. What state are you located in? Want to work on another Celica? 1ZZ-FE. I'd like to make a video of it with you. I work on cars too but the most I've done is replaced a head gasket. I don't have a cherry picker. My 1ZZFE is in good condition 88k miles but it would be great to rebuild it and take care of it using modern oil.

I am going to go do this right now

Appreciate you for this!

Got at least 10 rakes to fix and didn't think of putting saw dust in the glue. Super strong. Thanks!

What if you have no heat

I would only do this in a jam and then replace it asap. The tire sidewalls are not like the top tread and are very soft and easily rip or tear. You would be very lucky if you can even pull the plug tool without ripping a bigger hole. If anything patch from inside and again only in a jam.

Great video.. Do you have a video to rebuild it 1zz engine.. Thank you have a blessed day and be blessed

What kind of mower are you working on? I have a Husqvarna YTH2448T that has the same problem. I am still trying to get the rim off of the hub.

My Tacoma has got same problem but it is P0442 code. First it starts to smell gas, and what I did is Left up and slide the bed, this had access to the gas tank which exposes the vent valve. Since I got a new vent valve the C/E was solved.

Great vid.....it's so easy to make simple mistakes Btw, at hi rev the vacuum drops so the pcv opens wider to allow more flow through pcv Thanks again for vid

You saved the day thank you! 🙏🙏🙏

omg bro i didnt even think about it being the gaskets THANK U

My metal poles are bent maybe 20 degrees and just pulling them by hand does not straighten them out. Any idea how I could straight the posts? Thanks!

I don't think I've ever had a hive end up dead.

Why would you take the air out? Leave it in! (That’s what she said😂) But seriously.. there’s no need to remove the air

When I have 3000 frameworks, this work is expensive and requires a lot of time and does not exclude production faster 🤔

Wow, I'm impressed. Those golfers are a pest for sure. I used poison and it doesn't work. Thanks!!

Thanks for the video. Super helpful

Great video

sure but try it with it in the car still!

There’s a bitch named wendy jarrett she thinks you stole her boxes. Because of the KDJ brand

My celica gt is too sensitive that I just fix it close to smog check time. It runs well even with p0300 misfire codes.

You're a life saver

It's not a Stihl copy. It's a Zenoah clone, newb.😂

Have you noticed any changes in hibernation? And how does the queen mate

Very good, short and complete video. Thanks ❤

Thank you🙂

What size compressor for do you use? Is that a framing nailer?

Thank you so much! Saved my motor!

@Kinghaywood85 U say HIGHLY illegal. Is there a statute and is that everywhere or by state, etc. It's illegal to do wiring on someone's house without an electrical license but a homeowner can do it all day long on their own house. Perhaps patching your own sidewall works the same. Besides, I've never heard of them police officer citing somebody for a sidewall patch before Just curious. I wouldn't want to find out the hard way that you are 100% correct because I am considering not having to replace it $260 tire. 🙄

Does bleach bother the bees

If you tire is dry rotted, I would say by new tires .if your tire is new rubber is pliable and soft. This plug technique is totally doable.

Brilliant video. You have saved me time and frustration. The problem with Toyota is that they have designed too many different hose connections proprietary locking systems. To lower the fuel tank the fuel supply and return hose each end is different, the vapor canister is different (and the most challenging), the fill breather is different, the fill vent is different. Only the fill tube has the old school hose clamp. Very annoying. How many smart engineers came up with this foolishness? Thank you for teaching us the correct way to undo the hose.

Bru.........stop being that Stubborn Asian !! lol

Dam dude............Thanks for posting.......I have a 2000 GT 5 spd....love it.

I have the 2000 GT 5spd...........mine burns lot's of oil. Just did the Valve cover Gasket ... thanks to your video now i'm going to do this one as well.....The engine smells really bad exaust from the engine??? Is it due to this or the Exaust Manifold gasket?? Anyhow .....My Celica runs super nice and strong.....just it burns oil! Love my Celica...jet black and looks sharp....ppl gives me lot's of compliments!!

Thanks for the video. I tried it today, and it seems to me that instead of pulling the spring with the wire, it’s easier and quicker to wrap the belt around the tensioner and then stretch it over the last pulley with the spring already in place. I basically hugged the left rear tire to get both hands in there, and then pulled the belt with my left hand while grabbing the tensioner pulley with my right to bring it over the last pulley. You’ll have all the leverage you need, and it takes just a second.

Absolutely ridiculous prices for a large piece of extruded plastic. A 30 or 50 gallon plastic barrel will work fine, all that needs to be done is the base sealed, and a removable lid.