Відео

Hello sir , if I just want replacement diffuser only , I should need take whole bumper out ?

Tanks

Hello sir , if I just want replacement diffuser only , I should need take whole bumper out ?

Great 🙏 thanks

any possible way to get the t15 bolt to buy it?

What size release tool? I bought a universal one on Amazon and size 1,2 are too big, and size 3 is too small.

❤❤❤❤

I have been trying to find out how to do this for months and you are the first to mention the two different bits needed. Thank you very much

You have to remove the fckin bumper you fckin bastard

Thank you very much for you help! The front taillight bolt in my 2022 Cayenne was a little loose and you gave me great instructions on how to access that bolt and the correct 10mm bolt. Of course I dropped my socket, but the second time I put a piece of paper in the socket reciever and put my magnet in the extension. I retrieved the socket using the other access cover underneath the cargo net. All I had to do is tighten a 1/4 turn to reseat it. Thanks again.

Спасибо

Great video, thank you from England 👍👍

Спасибо большое!!! Жаль что раньше на час не нашел это видео, помоему я сломал свою фару пока пытался снять.

Great video thanks for the advice helped me a lot. Can you tell me how can I get a Ambilight wire through the door to get it through the cable spot where door is connected? I couldn’t find anything online

On my 2010 the buttons have recessed so they cannot be used - do I have to replcae the whole unit or is there something that lines them up correctly?

😆 'promo sm'

Красавчик, спасибо за видос.

The 2008 Gallardo Spyder is under the damn car by the way... I figured mine would be in the same spot so I took out all this mess and there was nothing there but other parts. I followed the lines down and finally read another post and learned in the 2008 they are under the car, in front of the motor under a triangle shaped panel that is held on with 4 torx screws, T20 I think it was. Problem I have now is, I cannot get the connections on. 1. They are extremely hard to get to unless you have a lift, 2. they are in a hard to get to spot even if you can get to them. 3. One of them is so close to what feels like a 2" cooling line the gauge hose will not fit because it will hit what I think is a coolant line. I was going to jack up the car but I was also reading that you can crack/break the windshield unless you jack up both sides at the exact same time. Pump up one a couple times then go to the other side, then back and forth. Not sure if it is true but was NOT going to take a risk breaking a $7,000 windshield, NOT. I also heard that they maybe a different type freon fitting to but not sure again. I was going to put gauges on mine as the AC will not come on, blowers work but no cold air and do not hear the compressor kicking in, but than again more than likely could not hear it if it did as the thing is f'ing load as H3LL. If anybody knows what else I can check before I find a way to lift it up and put gauges on it that would be great, I know it has some freon in the system as some came out when I was trying to get the hoses on laying on the floor. It can have some freon in the system but if there is not enough freon the pressure switch will not let it come on to protect the system.

Thank you very much! It helped

How many gram freon does this take?

Any video on installation?

Thank you for this very much!

Thanks for your video. I have the same problem. Even after the installation of the radio that did not match the COMAND knob, I worked for a few days. But it is not working anymore, I think that since I push the radio with a lot of force I have a damaged cable that controls the knob. I have to remove the radio to check if any wires are damaged. My fear was to put the radio back, since as you say it is a great challenge that nobody explains in most of the videos. Your solution has saved me. Tomorrow I will take out the radio and I will do it in the way that you indicate. Thanks a lot. Keep making videos so explicit, believe me, that makes a difference. Greetings.

thanks for your video, i wonder if I can get some video about changing rear center tail lamp?

Thank you

You save my lifr buddy

That looks like a Schwaben tool to release. Where can you buy it. without buying an entire kit.

Thanks for making this video. It was of great help.

Tnx a lot. Helps soooo much

The screw doesn’t come out of the hole

Why did you replace the unit?

Thank you

Nice ease

I'm from Brazil and it helped me a lot. Thank you

Thank you sir!!! The Urus uses pop clips on the inside so I figured the Porsche would too. Nope! 😂

is this similar for the MACAN?

many thanks. this video has helped me to easily disassemble this button module.

I have a 2019 Cayenne and the license plate screw is stuck due to rust I think, and it just spins, cannot be removed. Is there a good way to take it out? Do I have to remove it from inside?

Thanks for the vid. Where do you get the tool?

고맙다

Thanks man. Vid just helped me out a bunch.

You saved my body guy hours of work with this video much appreciated!!!

Cheers buddy! UK bodyshop, I thought before I risk breaking the black trim piece, I'll see if anyone's done a video on it. Result!

Any idea if you can reprogram those rear light to an amber flashing indicator instead of red light, when the indicators are activated?.

Thank you so much!!!!! I had this problem for a while on my Maserati and it pissed me tf off lol I couldn’t find a video and you are literally the only one ! So thank you! If you know how to replace a mirror switch of a 2008 Maserati Granturismo please upload a video I need help lol

Any chance you also did a video on removing the center tail light panel as well?

How much did you get this part for please