Відео

Nest thing not to do is get carb cleaner on gaskets because it blows them up and the gaskets wont seet in properly.

Dumbass that is a special made tool You made fucking isiot

This is very helpful 💯 I've previously avoided buying unnecessary new parts with some contact cleaner (car indicator stalk, dash switches etc) Yet didn't think to try this!... Worked for a bit then started evenly pulsing overload light again with rough idle/engine dropping out. Took off side of case w/o pull cord cleaned repeated this👆 and then other side. Cleaned everything removed and cleaned all connectors again. Sprayed contact cleaner pretty much everywhere to help clean the case... Did the trick! Been running 2x30a chargers for a good half hour now and it's not played up again yet! 🤞 (The off/engine switch pings itself free from the rocker when you remove it but is easy enough to put back, just twist it back to on then put plastic knob on and twist back to off *clicks*)

Ajudou obrigado 🇧🇷

Just did this with mine - Hyundai hy3800rv - and found the inverter which was potted has unused pin connectors protruding from the potting which were rusty and were likely shorting together. I cleaned all connectors including these and now the unit works 100%. I'm going to get some dielectric grease and apply a small amount to all the connections, I'm currently at the cottage and didn't have any but this video is spot on with helping me sort this out.

thank you!

Looks like a blue meanie from the animation, "Yellow Submarine"

Me podrías decir si el tornillo de regulación de aire es el que está en el frontal en la parte del filtro gracias y buen video

GREAT VID SO I HAVE A GALV TRAILER WANNA PAINT IT BLCK SO USE ECTH PRIMER THEN TOP COAT IT FOR GOOD RESULTS ?

NOT SAFE>>>>THEY ARE CHEAP TO REPLACE...If they break under way you CAN GET KILLED NEVER FIX A FROZEN STEERING CABLE...REPLACE $70

Thank you,you gave me a starting point. That makes sense. I only fill my inverter with 4 hours of gas and let it run out. It vibrats when it runs out of gas.

Your method made me got off mines. Subscribe to u for that woowoowoo 😊

Is ATF auto transmission fluid?

Thank you so mutch!!! Very appreciated your advice! It was accurate cause it solve my problem with my westinghouse 2200 .I was thinking that it was the end of it, but thanks to you it wasn't. Thanks!

Nice

You missed the idle jet on the top its the one at 12:00 O' Clock

looking forward to your next test on galvanized steel

Simple yet effective... Thx

You don't need the plate...3 screws into those holes,keep turning and it will walk right out

Just take the rod out and clean it then clean the inside tube!

Excellent video! Highly informative. I have a few boat trailer projects coming up that are both painted and galvanized. Your tips are definitely going to come in handy. Thank you!

Can i spray rustolium professional cold galvanizing spray over a previously hot galvanized anchor?

Great video bro. Nice& quick and I appreciate you sharing that we don't need to remove the carb. Well done

I used a 5mm armor proof steel plate and it bent the f ing plate💀💀💀 the flywheels is still not lose💀

Holly F, I don't have the patience for this guy...😢

Que medida de chicler de alta lleva?

I just bought a br1700 from the local dump/ buyback shop and it wouldn't start. It was pouring fuel out of the drain in the bottom of the carby bowl. I took the carb out and tinkered with the float. It all seemed ok. I put it back together and it started first try after putting fuel in it again.no more leaks. I will be taking the front off tomorrow and checking all the connections. I hope it will fix the problem of no generation. It is because of people like you that backyard mechanics can fix very simple problems. I will keep you posted as to the outcome of my endeavours. Thanks muchly for your video.

Thanks tremendously for giving me this confirmation appreciate it. I went to the electrician and he told me I was roasted, was better off buying a new bike and my bike was my source of income put my tools and everything in it. Did the oven trick and she ready to work thanks

Champion Kiwis 🥝

Hi thanks for furthering this, please tell me was it a permanent fix

Special note, just used your fix although didn’t actually notice that it fixed it until plugging a power device into it and then it was working. Up until then the light was still red on overload alarm and was assuming it hadn’t worked.

What shop?

Good idea mate. Ive got mine apart and it had me a bit stumped how to get lub through it. Im going to try Inox mx4. How is yours holding up?Thanks.

No special tools uses a thing no one has

Really thanks man. Best idea.🙏✌️

Thanks for the tip I broke my stator that I was gonna replace with this genius idea 🖕

Great info, thanks for sharing

did not work

So I have a Galvanized Boat trailer that I have already cleaned and strip the rust off of. Is my best bet To get some Zinc Gal coating to fill in the scratches and some other minor holes. Then spray the Etch primer over that. And then get a acrylic based topcoat?

Question: Can Zinc Gal Be Used On a Shipping Container Home Interior & Exterior ??? Thanks For The Awesome Review. ✌️🖖

I have one of these, same fault. Same thing fixed it. Cheers legend

guys i took a similar approach to this that worked. I used a spray bottle and sprayed isopropyl alcohol on all the possible electrical contacts and blew them out with a compressor, and my generator finally stopped saying overload. i cant believe it, ive tried everything else. i did leave the generator in the rain once last year, and I used it in the desert once, and it turns out the dust there is mildly electrically conductive, and there might have been a bad electrical contact, i couldnt find it individually, but spraying isopropyl alcohol worked for now.

S tour cam sprocket blown up yet?? 😂😂

how to remove the gold part tho

Thank you. my stressed our hubby asked me google anything to help solve this problem. Manual was useless. He is off to try out your suggestion.

Thanks for sharing this very helpful . GOD BLESS you

I dont have a wrench and tried to use a screw driver to keep it from turning. And bent the crap out of my screw driver.

thankyou

Bro, that is genius!! Thanks!!

Hi mate, are based in Sydney? was keen to get your advice