- 19
- 4 663
Darrell H
United States
Приєднався 15 тра 2012
linuxcnc Qtplasmac update
I thought i should update my new set up. I am running liner rails n the Y axis now and lead screws. sooo much better than belts.
Переглядів: 47
Відео
Day 2 ammo can flair.
Переглядів 524 місяці тому
this is my second run on the ammo can gasifier with the norther self reliance replica ejector. Today i disasembled the 1 in steel tube exiting the gasifier and found it was at least half plugged. it must have been from the 6.5hp gen pulling so hard. I cleaned it out and it was much better. Raining today :(
Ammo Can Injector test
Переглядів 324 місяці тому
This is a test of an air injector on the ammo can gasifier. It was a great success.
Charcoal Gasifier first test!!
Переглядів 1,2 тис.4 місяці тому
This was the first test of my newly built gasafier. I have the jets installed but i will most likely only use charcoal. I am also using store bought charcoal for now. I haven't had enough time to make charcoal yet.
Qtplasmac Oxcnc plasma build.
Переглядів 139Рік тому
just a quick video on my oxcnc plasma build. This is built on a JEGGS plasma table im using linuxcnc qtplasmac and mesa hardware. This is greatest thig to watch it never gets old. Im using a 50amp chinene blowback plasma cutter. with THCAD-10 for torch height. I have a THCAD-5 for hypersence but am still working on that. enjoy.
Ammo Can Gasifier with automatic AFR.
Переглядів 186Рік тому
This is my first test with Matt's (thriveofgrid.net) automatic AFR. This truley amazing. This was the best run on the ammo can yet.
Ammo Can Gasifier - Gen run
Переглядів 1,9 тис.Рік тому
This is my first attempt to run a generator with my ammo can gasifier. Defiantly a success! This is the result of over an hour s time. The generator is one i found for free on the side of the road. Could not get it to run on gas. I'm going to remove the gas tank all together. If you look at my mixer valve i started with a gate valve and could not get it to run constant. so i added a 1 " to 3/4 ...
Ammo Box Gasifier
Переглядів 518Рік тому
This is my first attempt at building a gasifier. Plans came from www.thriveoffgrid.net/ this guy is amazing!! The most amazing gasification products. This is a day vid of my first flare and a night flare.Im Hooked!!
RMRC Recruit Mini Wing - Maiden flight
Переглядів 1074 роки тому
This is the maiden of my new RMRC Recruit Mini Wing. This was also my first fixed wing flight. I was loving it!!! It was a bit windier than i would have liked but i couldn't wait. I need to find a bigger field for take off and landings. Stock RMRC Recruit Mini Wing PNP R9MM reciever
Diatone M3 - RunCam Split
Переглядів 1726 років тому
Finally got some nice weather and some free time. I love this frame.
P4P - Flight 2
Переглядів 426 років тому
P4P - Second flight.... I think I am in love. What a great machine. A little long still getting my bearings on post production.
How many cubic centimeters does the engine of the genset have? 196ccm?
it is a 208cc
Pretty nice, how long will it run? And do you have plans?
I had about an hour and 20 min on a full tank of good charcoal. after it cooled and i looked inside i saw it still had quite a bit left to burn. A shaker would help this im sure. I built it by fallowing Thrive Energy Systems he has a you tube channel and website. very amazing work. he has a 3 videos on building this.
What camera are you using? The colors look really nice.
Great vid mate! Just trying to get my Mini Recrut / AR Mini Wing ready to rock!
Ok i will work on something to post.
Hey can you post a vid of your install/setup? I am thinking of buying the Diatone GT-M3 v2 and want to install a Runcam Split, not sure how it will turnout/work. Thank you!
Oops... No GoPro. On board FPV CAM.