Відео

@@Tanyewes thank you!

@@EZ_27 what lights

@@jetcontracting4244 yep I always say this! 99% of the time I do this just because you don’t know if the mount will land where you end up putting the box! Nice tip

@@brianhamilton962 if you have enough work we can travel we’re probably 8 hours or so away

Want this done for football season coming up

@@brianhamilton962 probably could would be looking at 7500$ or so

@@quicktechav If wifey on board it’s a go fo sho

@@brianhamilton962 okay! 979-571-5131 kermitmoore@quicktechav.com

@@Micro_Pixel got to do what you got to do lol

@@quicktechav Call a technician?

@@Micro_Pixel yep or do it yourself it’s not hard

@@quicktechav Do adapters work too?

@@senortrolls2617 I’ve done plenty of 86” tv on 2 metal studs with 4 toggles all into metal studs

Thank you! have you ever encountered an issue where one of the four toggle bolts won't screw in after being placed in the wall? The first three toggle bolts went in smoothly, and their corresponding screws were easy to secure. However, the fourth bolt is giving me trouble. I've tried three times with this one hole, and I've verified that there are no obstructions like pipes behind the wall. I can thread the toggle bolt with the screw outside the wall without any issues, but as soon as I place it in the wall and try to screw it in, it feels like the threading on either the screw or the toggle might be bent, preventing it from securing properly. Any tips or advice would be greatly appreciated.

@@senortrolls2617 make sure that

@@senortrolls2617 make sure that the toggle is all the way in and straight laying flat to the back side of the metal stud if that makes sense and always hand thread before hitting with drill.

@quicktechav Thank you I'm gonna try again with my 4th bolt for this hole 🤣

Yes no bigger than 65l”

@@NerdNerd-vz3uv standard here is 500 to one gig

@@quicktechav god damn I need to get me into this

@@quicktechav I only get 20 wired 😭

​​@@NerdNerd-vz3uvmy friend, are you maybe confusing Mbps (bits) with MBps (bytes)?

@@azimmorganam I might be idk

@@raymondsaunders9938 from another plug in the attic

@@idkimdrunk7090 yessir!

College station Texas

@@quicktechav is there a better place to contact you?

@@pedrozamariq customer found a 3d printed one and I installed a electric outlet above in ceiling

@@wscottfunk yep I agree all for looked I think it looks better than a blank in my opinion though

​@@quicktechavit looks great! 👍

No I’ll use any brand

@@sunkneee okay.. the only place they built the home to put the tv.

@@timparker5825 yes but you have to be in the same network at the matrix and connect to its up address

@@quicktechav gotcha, so I have to plug in the cat 6 directly from the matrix to the pc? Or can I plug the matrix to an internet router?

@@timparker5825 matrix and pc into the router. Then make sure their both on the same ip scheme

I have the matrix and PC plugged into my T-Mobile router. But when I put in that IP address 192.168.0.100 I don’t see a login screen.

@@quicktechav finally got it to work, thanks

It came with on this one

@@michaelpeele3451 to be under 1.5 minutes I believe

Yes

@@crider46 it is the best I could do with what I have. All you have to do it’s pry and separate the best you can while keeping it hot. The sealant is not easy to get through you will find what method works best on doing this. There are other videos that may be better on removing the lens

@@crider46 I believe it said like 400 in 10 minute increments but the heat didn’t last long so I used a flat head and heat gun it was easier. But honestly that is the hardest part is getting these things open.

@@quicktechav can you show more on the controller and how that all works

@@crider46 it’s all installed now but I can point you in the right direction. Black goes to negative terminal on battery red goes to positive terminal on battery. Then the spare cable I hooked up to one of my aux buttons inside. As far as from controller to inside headlights you can hook those 4 pin connectors anywhere on the controller outputs

They went from cox to suddenlink to Altice and then optimum here

@@yakubasheriff6088 thank you!

Try using a step triangle bit

Snap AV

Depends on the tv you have to measure

I’m not a fan of using four separate mounts. They make professional tv wall mounts. They are more expensive, but you don’t have to worry about getting all four measurements correct for the mount. Install looks clean though!

@@zoeboifresh1000 you’re correct just keep in mind your shipping times! Hard to get one mount quickly vs something like this.

@@SaltMinerOU812 right! It is nice especially if you don’t know how to work with electrical

I sent to one tv

I wanna see the whole process

@@builtdoor his router was in a different room I believe we did the same thing in the other side

@@SpartyHR I hook it to a specific speaker some of the switches have a audio out port on them

You can but not merge to one big picture because hdmi has to go into controller for that and TVs don’t have a hdmi output only input

@@hibrucetzenh6170 about 200$ of local

That’s what they wanted we just make it happen. 😂

Yep or let us install the borderless micro led video wall if you got the money

College station Texas

Untwisttool