Відео

This doesn’t work in cold climates

better is put the tire in a boiling water for 30 min much easier. but well done buddy

This is a very well done video of installing a dog door. Thank you

after literally hours, tears and an immense feeling of defeat, this worked like a charm, thank You!

How's it holding up?

This is the most complicated method yet.

Great job made it look easy ! Tomorrow I will give it a go , Thanks !

What happened to the plants between the stones? Did it not work out? We wanted to grow creeping thyme between ours, so I’m curious to know why you switched.

thanks

Looks like a great product. One concern for me would be water drainage. Do you see anyway to install gutters on it to direct the water to one end?

You have to leave at least ³/⁸ of a gap by walls for expansion

I just ran into this problem today. I really didn't think I'd be so lucky to find this video. Thanks much for posting!

The instruction say to pre-drill with 1/4" bit, but that is too big for the Palmram screw, so I assume they mean pre-rill the PANEL, but not the wood? Thanks.

So, what I’m getting from this is… 1. Have a work table that you don’t mind drilling into. (Seems like a standard apartment in the city furniture piece, that everyone has.) 2. Have 9” wood blocks. (You know, those ones that are just lying around.) 3. Go buy washers and screws. This is effective, yes. But is it a practical solution for city dwellers without vehicles or workshops and an abundance of tools? No.

Does water leak through the screw holes?

Did the beetle tape come with carport? How long did it take to install? Want to get the 20x20

Thank you! Thank you! Thank you! Best technic ever for putting on that fkn tire 😂!!!

Great Job! It turned out beautiful!

caulk the door aswell

Straight and to the point. This worked! Thank you!

Need a front rib replacement for a 12x20 carport shed . Do they sell replacement parts and how to find them?

How many days did this project take you? Looks great!

But how do you get the screw out?? Mine is stuck.

Vinegar was just what I needed. Thanks!

Mine came with solid rubber tires (HiBoy S2 Pro) and they are rock hard with hardly any flex at all. I'd like to replace them with honeycomb tires but they look like a pain to remove 😩.

As a single mother, I was struggling to find a solution for my dishwasher until I stumbled upon this video. Unlike others that had me dismantling the dishwasher with no success, this one provided clear, effective instructions. My set up isn’t exactly the same but it didn’t take long to figure out. The relief I felt when I heard my dishwasher draining was immense!! It saved me so much time and hassle. Thank you for this! 🙏

Hey Jed! Does the lens work well for getting a spot focus? Does it work well for heating experiments? Melting metals? Thx

Hello!! How long did that take for the grass to die under the plastic? Great video! Thank you! 🙏 😊

Best video- great job on explaining. Getting ready to do one.

So you basically need to be an octopus mounting this s.. great..

I most definitely needed this! I have the same exact issue and I thought I was going crazy cause it wouldn't come off. Lol

Nice

Also, please let me know if you know of any other uses for this Fresnel Lens

Good job on the video. I bought one come with no manual!

In my area the weeds would take over between the pavers

By code you need to be 36" from your electrical panel

I like that you stress it's only an eighth of an inch needed - I see so much gloppy dirty caulk. Thanks for a great video and information! I am about to do my own kitchen & your video sure gives me more confidence.

Sprayed, vinegar, lime away, and wd40. It's still stuck. Went to HD to see if they had a tool and they do not. So.... wtf last time I called a plumber out they charged me 180.00 for the service call then told me it was 1300.00 to replace my tub spout. Cost me 40 bucks to fix it myself. I have less trust for plumbers than I do for politicians.

The colored mortar looks good!

Do you think it will be just as Efficient if I’m using 2x6’s to screw the panels on

Looks great! Thanks for sharing. It doesn't look like you used edging between the pathway and the mulch that surrounds your plants. Do you find that that mulch stays in place enough? I'm a hopeful DIY'r and can use all the info I can get.

i started something like this last summer, only on a much smaller scale. i wanted to grow grass between the joints. But, i found that it was hard to pack the soil in the joints, which exposed the sharp edges of the flagstone if you didn't step directly in the center of each stone. the soft soil would get kicked up, or pushed down. Wondering the best way to counteract this? or is that just something i have to put up with until the vegetation really takes hold? (even after grass grew it was very soft). Thanks!

what do you think is the MIN pitch needed??

Finally someone is showing us this thank you

What is the slope? You stated it wasn't enough and that was one reason for leaking.

Dude, thanks for this vid!

Why do you screw into the peaks of the corrugation and.not into the valleys of the corrugation? Thank you!

Hey! We're in Utah as well and the cheap corrugated metal one that our landscapers installed is failing after 1 year. What was the cost per sheet if you don't mind me asking?

That looks so pretty! 😍

Im watching this video a second time. Its a absolute must to use the large washers. I tried using the smaller ones and destroyed some of the tire due to the hot screw and spinning drill bit. Also try to be mindful of where you place the screws because too close and the threads damage the rim.