Відео

I’m kind of sad and happy that I found this video You guys explain a whole lot better than anyone at my shop has 😭

Perfect

Very nice

How to apply tire man

These auto duckheads suck balls. Far too easy to damage the sidewall as it plunges down. Crap.

54534 Crona Path

Brookhaven College professional baking study guide 2 QUIZ PRACTICE TEST exam 2 with the questions and answers 😅 .

17:02 Is it important to always put the spatula away handle-first, so that it has to be grabbed by the slippery end?

As a factory-trained Ammco service tech I've collected a decent amount of genuine Ammco parts over the last 40+ years. I'm retiring and have a parts inventory list if you are interested.

you saile this one

Never clamp a wheel inside out. Always use the clamps to grab on the outside of the wheel

Thanksgiving cause

Thank you! I needed a refresher. I haven't resurfaced rotors since I left Universal Technical Institute back in 2005. I just got a lathe for my shop and this was perfect update for me. I'm using the same lathe as you.

Well done, Stephanie

Thank you so much sir

Hunter! pls make the machine that can work both on car and motor cycle tires in one machine.

Thanks for posting this! I used to work in a machine shop but never saw how rotors were machined. Just did a brake job where the rotors were machined and now I understand why one of them was returned to me with .010" runout!

Gracias hermano estoy seguro que si salistes un poco pedo gracias por compartir todo chingon y chido

This machine is way better than the Coats 1250. The Hunter GSP9700 is easier to operate and learn.

Nice machine but Duquesne made in Belgium is for me the best

If you balance a wheel and it comes out ok, take it off the mount and try it again should it be ok? my tire guys says it impossible to remount and see if it is still ok. Thank you for time you took to explain all this

Thanks but you can Fs cut this video down by 10 min at least

Since the measurement for the outside of the wheel lip surface is essentially just a way for the machine to know the width of the wheel (the outside measurement function became available at the same point in time as we no longer had to measure the wheel width with the calipers) , is there a way to enter the width of the wheel if it happens to be stamped on the wheel somewhere?

That last and vey important step ( smooth the surface with sand paper) is what I should say should be done with the same machine, so not wearing so quickly a brand new originals oem braking pads, that for sure star an unevem surface again an so on , and you will realize that changing brand new rotors is cheaper amd ypu always have a brake sysytem with fuul power ready for any braking emergency. I appreciate this good video, and good luck

What may be the issues

I have question for you Our hunter balancing machine have error When you apply loadforce After spinning the time its says Too much speed And stops

.... Das ist kool... danke

QM is helpful for faculty to improve student success.

Em portuense

Interested can I work for you

I love Hunter's equiment. One of the best equipemtn in the U.S. I've been working with them for over 20 years.

Looks like too much work for on-car. Someone with less skill or badly calibrated machine can ruin the rotor anyway. I see in the comments, people do have positive points about it. But what if the rotor was installed not on the clean surface and so on.. It is always better to take it off and clean inside. + for the customer, save some now, it can rust-in even more. Especially for mazda I would want to pull that rotor off and clean inside. They sometimes rust-in badly, to the point of need to cut that rotor to remove..

How can one get this training? Am very much interested to learn.

Hello I hope you are well I do tire balancing parallelism I would like to work with you one day

My God it's a science now to change a tire....wow

sir i want to work with you.

Rubish video,,,,,,,,,,,,,,,,,,,,,,,show on 20´´ runflat with 35 profile....

This aint gonna work on a car with an lsd. or it will do some damage at best

मशीन मुझे खरीदना है

Assalamu alaikum bro how are you bro your work is very nice alhamdulillah very good bro i am also a technician tire mechanic like you bro my name is md arif hussain bro i am a bangladeshi citizen bro can you give me a job i have eight years of experience i am 20 years old

Please how much the cost?

12 clock tpms or it can break. At your pace I would be out of business

As a mechanic I say its way to complex to balance a wheel! We have a Schenk balance machine for about 35 years never had isuses with balance a wheel! The biggest problem from this kind of machines is the horizontal axle!! In industries the always work with vertical axles this machine hunter en all of others clones the are not good build, what do you think when the roll make presure on the vertical axle more difference you have and thats wat you don’t want when you balancing!

Job for me I am wheel alignment and wheel balancing technician

Job for me

Price kya hai

I just want to understand, because every I boughttire alway charge the wheel balancing

Dommage qu'il n'y a pas une traduction en français ❓

Im in automotive class and hes making us watch the video 10/10 video very helpful thanks mr gurrero