Відео

Terminals that don't snap off at 4nm with this version then

Looks like it's not really convenient to assemble batteries in vertical state and in the limited amount of space dedicated for BMS.

Hi im interested to buy one I have already a jk Inverter bms and 4.3 inch display. Have you olso an AliExpress shop ?

Very good

Now add some paint on each screws, to be able to easily check if they do not unscrew

One main critic, the screws on the breaker needs to be checked periodically, heating/cooling can make those kind of connection lose. In this design, they are not accesible.

Bellissimo Video!! TOP

Any permanent external wires should be located on the back of the enclosure.

I have V4 i don’t like the cable connection inside the box. I prefer these busbars.

I have the prevous version with the breaker/switch at the front. >50A the breaker starts to warm up significantly... maybe that is the reason to get rid of it....? Although I like the switch to disconnect the battery quickly for maintenance (off course not under heavy load... don't trust the switch that much)

hello! an interesting update. now you added a fuse, but there is no switch anymore..... that switch i miss too ....

No breaker on the outside, not a good move.

Who manufactures the BMS in this battery and what is its charge/discharge amp rating. What is the warranty of the BMS (since it's the part that's most likely to fail)?😨

Wow

Почему не продаете на али экспресс?

great unbelievable

I costi?

Do you do a 24v 280 version, maybe a 24v 560amp, or same case with two 24v sets and two bms?

Hi, what cables should I use for the P- and B- cables of the BMS for a 16s 2p 48v system?

But Heating pads not to use no place

30kwh 16 cells,not posible

Heating pads ? For use outside garage

OTTIMO SISTEMA!!

ratchet wrench for lithium cells please ?

hello thanks for the video, what is the name of the tool to screw the bolts, the one that makes a report to say that it is ok

Hello and congratulations again for your great video I had a question: can the JK-PB2A16S20P communicate easily with a victron multiplus II 5000VA? what equipment do you need special cable in addition? I'm trying to find out about the bms because as I have a large 24 volt 1300AH battery pack I would like it to work perfectly before investing in the BMS and the victron multiplus II! laurent

how much Nm for the 2 breaker connections?

I've sent an email tO the website contact, 3 weeks ago...no answer. No need to advertise if there is no follow up.

great👍👍👍

Interesting layout, quality assembly. But, unfortunately, BMS-JK of this type do not work normally.

It is obvious as hell there is ZERO CELL COMPRESION!!! Shame on you EELBATTERY!

I don't see any kind of grounding screw/terminal??? And there is no support directly under the end of the PCB when you hook up the BMS plugs. The PCB bends way to easily and can crack the electrical traces.

How to connect two JK BMS, the configuration (UART1 protocol = ?), main and secondary JK BMS, currently has RS485-1 or which port, thank you

Hey Miya! send me a link, where I can buy this box. Thanks in advance.

Здравствуйте, подскажите пожалуйста какой мощности у вас стоит автоматический выключатель? Спасибо за ответ.

I got mine after 2.5 months. The construction went well. The screws of the compression plate were too short so I bought longer ones. Unfortunately two Eva foams were missing. My cells are EVE 304Ah. Up to now I'm satisfied

The success will depend on what BMS is used, what balancer is integrated and how the connectivity with the external environment will be done. Cons: If one or more cells are not performing like expected, the replacement is not easy!

Bellissimo video!!

I would love to see a version of the 4.3 inch display on the Vertical EEL battery box. @eelbatteryofficial @EELBATTERY-Miya

I have 3 on order.

EEL Battery boxes are the best

EVE has not allowed the flat mounting position which means EU inurances will not pay in case of a fire and what not if you abuse EVE cells this way. You are not allowed to at least here in central Europe / EU.

2:24 - I suggest to have a close look on the big red and black wire which connect to the battery terminals . The ring lug that gets connected to the terminal has to be in the right position which means the ring itself needs to be on the bottom. Otherwise the crimped ring lug would later press against the top of the cell and pressure from the terminals screw would be pushed into the top of the cell. 2:07 - shows the black cable ring lug in the wrong position cause it has to be in the opposite position. Now the flat metal part of the ring lug is closer to the table where it should be close to the ceiling. 3:03 - shows the red cable with ring lug but now in the right position, while the black on the left half is still wrong mounted cause the terminal screw will put force on the ring lug and that will lead the pressure into the top of the cell which is not really good. Not great and I have not seen any EEL video or manual which emphasizes on this topic how the ring lugs should be positioned if you screw them into the circuit breaker If you had done it wrong like I had done then you would have to unplug the front plate and disassemble the whole circuitbreaker and box assembly to get to the point where you can unscrew these 2 cable to turn them around AND i also had issues cause the red cable to the red terminal from that MCB was like in this example TOO LONG and put pressure on the circuit breaker which then was hard to get into the hole. Big mess if things go wrong and it needs a better manual and better videos - same for the whole mess regarding temperature sensors and where they have to be placed and bolted too. Finally: my pcb A and PCB b arrived only partly assembled which I learned the hard way cause at the end I had screws over where I found out that my PCBA and PCB BMS connection boards were only fixed with just 2 scews each. Bad move to not mention these topice in the videos and also not in the manual . These topics are important.

Buongiorno ho montato la batteria ma mi da errore, devo collegarmi con il cellulare e sbloccare il bms in carica e scarica? Quale app devo scaricare? E la devo comunque accendere ma mi da la luce rossa fissa

My case has just been delivered after about three months. The local distribution partner (DPD) didn't provide any track/trace information so I was really surprised to find it on my doorstep today. Anyway, it's finally there and I can proceed with the installation of my EVE 304Ah batteries

its possible to buy only case ? Without bms ? To Belgium ?

A wonderful clip, showing how the power JK (bat +) wire is extended.

Macie na stanie w EU ??