Відео

Ciao. Dov’è questo sensore?

P0071 arza kodu çıkartıyor aracım dacia dokker renault dokker. Bu parça motor bölümünde hangi kısımda olabilir P0071 Ambient air Temperature sensor range performance

Salutare ! De unde sunteți ? Sunt interesat de un schimb de distribuție! Puteti lasa un contact?

Salut Adrian o singură întrebare dacă poți să îmi răspunzi . Cum îmi dau seama dacă nu a sărit de la punct și cum știu dacă e la punct dacă nu mai sunt semnele de pe lanț cu cele de pe axele cu came ?

Did you solve the problemhave that same problem

What causes timing to jump on these engine's did complete chain kit replacement twice in one year

Not work on combo

salut. la cat ai schimbat distributia in general? 60k conform manualului? Mersi

Can I have a phone number please... I v same pb on my w205. Thank you

Hi! Recently changed the intercooler at a GLC 250d 2018. At the service, they completed the coolant but the white receipient dors not seem to contain any coolant. Is this normal? Is there a way I can reach you ?

Salut, mersi pentru sfaturi La ochiul liber nu se vedea nimic Am refăcut lipirea a celor 5 rezistente și funcționează 100% Mersi!!!

Trebuie obligatoriu stearsa erodarea sau porneste de la sine?

How did you bleed the system?

У меня такой-же код ошибки,насос в зборе обрыв цепи.с разъёмом всё хорошо, что нужно зделать?

Client complained about coolant loose and no marks were left under car. Intercooler cooled by air and coolant seems to be the issue.

Hello sir i need the procedure for pump duse iq adjustement Its tje good procedure?

Una pregunta Tengo este tipo de auto y no enciende comenso a perder fuerza Asta q se quedo totalmente parado y enciende pero no acelera

Działa dzięki :) pozdrawiam

Salut daca se decaleaza de la semne din cauza la intinzator sau patine se stramba supape sau doar o pui la semne?

Unless video

So I took my car for 135k service interval and now they are telling me that I need to replace timing chain I thought these can last for long. I bought it new in 2017. Any advice?

Are there any other known fixes for this unit? I have the exact same unit in my Golf but is not working (throws an error). I took it apart, resistors seem to be fine (10 and 63ohms) and solder joints seem to be intact.

Any tips on removing crank shaft pulley bolt renel capture

My Combo 2021 has wireless ignition key and this method doesn't work 😔

Pt ce e buna metoda asta.ce rol are?

I need to change this, any tips?

Any timing tools needed?

Salut, ce simptome avea mașina înainte să înlocuiești releul? Mersi frumos

Salut Adrian Cum ai scos capacul? (la mine se desprinde ok in partea de jos dar inca il tine ceva in partea de sus, desi e usor elastic, aduca n-am uitat vreun surub pe-acolo) E o garnitura acolo sau doar vreun mastic? Multumesc.

Hi. Need valve clearance on 0.9 tce 3 cyl.

Nic nie trzeba kupowac. Ten sposob uszkadza z czasem cięgno ktore uderza w ogranicznik. Polecam ten sposob ( P2015 WV Patent ze śrubką i problem znika )

1132A176 is a replacement to this part?

Never work with me...

Ai idee dacă și la Audi A6 2010 se poate schimba tot așa fără a da jos galeria?

Çok saol

I had exactly the same problem, you cannot buy the balancer module driveshaft individually. The whole balancer module gear assembly has to be purchased at roughly £700. This I did but to find that you cannot take the new drive shaft from the new gear assembly and insert it in the place of the old drive shaft ( the part you show, with the broken teeth). The reason being that the new driveshaft has slightly a different design/shape due the obvious manufacturing fault and it does not mesh well with the old parts. It's very noisy. To replace the whole gear assembly means taking off the crank pulley, timing belt, engine side casing etc etc and is a big expensive job. I have now driven the car for a two years without the balancer module attached. The resulting issues that I've had are: there is now more higher frequency engine vibration (obviously... you have removed the part that dampens the engine vibrations/harmonics), also the gear/s that are at the bottom of the engine that are driven off the same gear that drives the balancer module gear assembly, for example the oil pump, which in my case now seems to have an intermittent problem of not being driven properly when at idle. I believe this is because there is a gear that drives the oil pump which is a clutched gear, and the slack (or reduction of friction/drive pressure) in the gear system by removing the balancer module, has upset the ability of this clutched gear to engage/disengage at the right engine speed. Basically when driving normally the oil pump works fine, once the car is warm and the oil is thinner, when you pull up to a stop light the low oil pressure warning light comes on. My conclusion is as above for the cause, and you can even hear that there is slack gear or something along those lines making quite a lot of noise at idle. When driving normally everything seems fine. Two years it's been like this and the turbo hasn't died yet so the oil pump must still working within reason. Other issues I've had with the car is the classic egr/dpf soot build up. The whole intake manifold was full of soot roughly 75% of the manifold was blocked up, probably due to a dodgy egr valve and the fact that I tow a lot. These engines definitely need a catch can to reduce the oil vapour from the head being recirculated through the EGR valve.

what year is this model?

Se potriveste la passat2.0 tdi cbbb?

Salut, am și eu proema asta. E cineva pe aici?

Helpmi

Thank u adrian very nice✌️😎

Nici lanțul nu mai e ce a fost! E mai ieftin de schimbat o distribuție pe curea si cu interval de 200mii km e chiar peste lant!

Hi, do you have email, how I can contact you? Im inetrested in buying this part.

Salut ! Mai ai?

Can the timing chain be done with the engine in place?

Unde se afla Z35 la un golf5 ? Partea pasager sau sofer ? M-am uitat pe nste scheme si nu sunt foarte explicite

Cei ce se inspiră de aici, aveti grija, pe axul motor se află o săgeată mică, aceea trebuie aliniată cu zaua colorată - in acest video nu se vede, fiind acoperită de surubul pus pe vibrochen. Să nu fiți duși în eroare că se aliniază cu pana de pe vibrochen

A-ti refăcut lipiturile si a functionat?

Mulțumim. Am o problema la pornirea la rece. Am schimbat bujiile cred ca ar fi din cauza lui.

Interesant clipul char daca e scurt poate pe viitor o versiune mai detaliata cu tot procesul de la descfacut montare remontare ar fi interesant .