Those aren’t the right plugs to begin with, also the bore in that cylinder is likely scored. If the leak was bad enough it could have hydrolocked the cylinder.
looks like you didnt have to remove the gearbox actuator or plumbing, saves alot of work and time, was there any codes that you had to reset after this?
You know a lot of people rubbish the Mondial QV. Nevertheless, take the left rear wheel off, remove the wheel arch liner and blow me down start removing the clutch. Takes about 20 mins from opening the garage and you're undoing bell housing bolts. The east-west engine configuration of the 308,328,and Mondial's before the "t" are so easy to work on. The starter motor is probably the most difficult ancillary to access. Cam belts access through the other wheel arch. I love the 348,355,360 F430 and on and on. But the maintenance effort and resulting cost is beyond the "average man". What my local dealer would do for $8500 AU, I did for $750 AU. And I would have done a much better job...why? Because it was my car so I took my time and care. Thanks for the Video guy's. Marc
My car is Ferrari f360 modena (2003y / 66,000km) 1. 02-10-2018 : Ferrari 360 genuine f1 clutch set,, clutch bearing, pump reray, f1 pump exchanged (because gear missing) 2. After driving for about 200km (for two days) is good, normally operated gear(1,2,3,4,5,6,r). 3. But the gearbox warning light came on while slow driving.( video file attachment ). 4. 1, 2 gears, reverse only works. Gears 3, 4, 5 and 6 do not work. In a garage where F1 clutch set was replaced, it seemed to be a mission synchronizer failure. Ferrari gear do not work well in other garages. There may be other causes.
Those aren’t the right plugs to begin with, also the bore in that cylinder is likely scored. If the leak was bad enough it could have hydrolocked the cylinder.
My ac squiking when ac turn on
What year is this van???
What were the codes?
Did it actually fix the issue?
looks like you didnt have to remove the gearbox actuator or plumbing, saves alot of work and time, was there any codes that you had to reset after this?
How Much oz Freon take?
2 brains and 4 hands and 6 hours later done. I could've had that done in one hour lol
Where is the ac line located at
Great video! Stark contrast to guys with long video of blah, blah, with only moments of vehicle. Hope it catches on...
Just had this same issue on my e93 M3, thanks!
haha, a guy in bathing slippers working on a ferrari -priceless!
I have a 2004 , I changed my alternator yesterday and now my ac doesn’t blow cold or sound like it’s kicking on
You know a lot of people rubbish the Mondial QV. Nevertheless, take the left rear wheel off, remove the wheel arch liner and blow me down start removing the clutch. Takes about 20 mins from opening the garage and you're undoing bell housing bolts. The east-west engine configuration of the 308,328,and Mondial's before the "t" are so easy to work on. The starter motor is probably the most difficult ancillary to access. Cam belts access through the other wheel arch. I love the 348,355,360 F430 and on and on. But the maintenance effort and resulting cost is beyond the "average man". What my local dealer would do for $8500 AU, I did for $750 AU. And I would have done a much better job...why? Because it was my car so I took my time and care. Thanks for the Video guy's. Marc
as of 300 HP the engine had to be placed long (T architecture), despite the nice old V8's
@@EricMeijer007 Interesting, cheers. Marc
Lindsey Stirling. Nice
My car is Ferrari f360 modena (2003y / 66,000km) 1. 02-10-2018 : Ferrari 360 genuine f1 clutch set,, clutch bearing, pump reray, f1 pump exchanged (because gear missing) 2. After driving for about 200km (for two days) is good, normally operated gear(1,2,3,4,5,6,r). 3. But the gearbox warning light came on while slow driving.( video file attachment ). 4. 1, 2 gears, reverse only works. Gears 3, 4, 5 and 6 do not work. In a garage where F1 clutch set was replaced, it seemed to be a mission synchronizer failure. Ferrari gear do not work well in other garages. There may be other causes.
How many hours was this?
5-7 hours
No se puede apreciar nada
DO YOU SPECIAL TOOL TO REPLACE CLUTCH THROW OUT BEARING
Your going to need a clutch alignment tool to make sure that its center.
ONCE I REMOVE THE CLUTCH, DO I NEED ANY SPECIAL TOOL TO PUT THE CLUTCH,DISC,BEARING BACK IN